WAGO 750-486/040-000 Manual Download Page 75 | Manualshive

Page: 75 / 102

background image

WAGO-I/O-SYSTEM 750 XTR

Commissioning

75

750-486/040-000 4AI 0/4-20mA NE43 Ex i XTR

Manual

Version 1.0.0

Table 42:

Monitoring

Menu Item

Option

Description

Process value overview

Channel

Display of the bus channel

Measured value

Display of the calibrated input current in milliamps (mA).
This is a 32-bit value.
If the channel is deactivated, “N/A” (not available) is
displayed.
The measurement value is read cyclically from the I/O
module.

Process value (dec)

Display of the process value in decimal notation.
If the channel is deactivated, “N/A” (not available) is
displayed.
The process value is read cyclically from the I/O module.

Process value (hex)

Display of the process value in hexadecimal notation.
If the channel is deactivated, the process value (hex)
“0x7FFF” is displayed.
The process value is read cyclically from the I/O module.

7.1.1.4.6 “Information” Menu Item

This area provides an overview of the specifications for the I/O module used.
You obtain information about the following points:

•

Item number

•

Description

•

Software version

•

Hardware version

«
...
73
74
75
76
77
...
»

Summary of Contents for 750-486/040-000







































































































Reviews:

No comments

Related manuals for 750-486/040-000

Brand: GE Pages: 2

Brand: XOXO Modular Pages: 13

Brand: Balboa Water Group Pages: 28

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: GE Pages: 425

Brand: Galaxy Control Systems Pages: 5

Brand: Hach Pages: 36

Brand: Hach Pages: 72

Brand: UNICORECOMM Pages: 32

Brand: UNICORECOMM Pages: 7

Brand: UNICORECOMM Pages: 26

Brand: UNICORECOMM Pages: 25

Brand: Vacon Pages: 50

Brand: V2 Pages: 116

Brand: V2 Pages: 8

Brand: V2 Pages: 25

Brand: V2 Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands