WAGO 750-486/040-000 Manual Download Page 77

Page: 77 / 102

WAGO-I/O-SYSTEM 750 XTR

Commissioning

750-486/040-000 4AI 0/4-20mA NE43 Ex i XTR

Manual

Version 1.0.0

The following status messages with corresponding additional information are
displayed:

Table 43: Status Messages – Possible Status Messages with Additional Information

Status message

Error type

Channel

Status byte

Measurement range overflow

Warning

0x42

Measurement range underflow

Warning

0x41

User-defined limiting value
overrange

Warning

0x04

User-defined limiting value
underrange

Warning

0x08

Short circuit

Error

0x50

Information

0x00

Wire break

Error

0x60

Information

0x00

Channel deactivated

Information

0x00

Measured values in permissible
range

Information

0x00

The status messages are displayed with assignment of the relevant I/O module
channels.

Figure 36: Status Messages in the Application Window of the Parameterization Dialog

Click the

[Delete]

button to clear the status message history. The history is

automatically cleared if you interrupt the connection to the I/O module or
close the parameterization dialog.

7.1.1.7

Status Bar

The following information is displayed in the status bar:

•

Status indication with display of the currently executed action as text or the
respective error message if an error occurs

•

A progress bar is displayed as the actions are executed

•

Online status

•

IP address or COM interface

Figure 37: Status Bar in the Parameterization Dialog

Summary of Contents for 750-486/040-000







































































































Search results

Summary of Contents for 750-486/040-000

Reviews:

Related manuals for 750-486/040-000

Brands by name

Popular brands

WAGO 750-486/040-000, Manual

Search results

Summary of Contents for 750-486/040-000

Reviews:

Related manuals for 750-486/040-000

Brands by name

Popular brands