Wacker Neuson DPU 4545 Operator'S Manual Download

Page: 57 / 92

10 Troubleshooting

100_0202_ts_0008.fm

1. Pull out jump-start and connect clamping tongs of the red jumper cable to the

jump-start.

2. Connect the second clamping pliers of the red jumper cable to the positive

terminal of the donor battery.

3. Connect the clamping pliers of the black jumper cable to the negative termi-

nal of the donor battery.

4. Connect the second clamping pliers of the black jumper cable to a ground

point of the machine e.g. on the engine block.

Help starting

5. Start engine.

If the engine does not switch on after 15 seconds, abort start attempt and
Wacker Neuson contact partner.

6. Let the engine run for several minutes.

Disconnect the jumper cables

7. Disconnect the clamping pliers of the black jumper cable from the ground

point of the machine.

8. Disconnect the clamping pliers of the red jumper cable from the donor bat-

tery.

9. Disconnect clamping tongs of the red booster cable from the jump-start and

press jump-start in.

10. Disconnect the clamping pliers of the red jumper cable from the positive ter-

minal of the donor battery.

Pos.

Designation

Pos.

Designation

Jump-start

Negative terminal of the donor
battery

Negative terminal at ground
point

Positive terminal of the donor
battery

Black jumper cable

Red jumper cable

Summary of Contents for DPU 4545





























































































Search results

Summary of Contents for DPU 4545

Reviews:

Related manuals for DPU 4545

Brands by name

Popular brands

Wacker Neuson DPU 4545, Operator'S Manual

Search results

Summary of Contents for DPU 4545

Reviews:

Related manuals for DPU 4545

Brands by name

Popular brands