background image

1 Foreword

6

100_0000_0002.fm

1

Foreword

This operator's manual contains information and procedures for the safe opera-

tion and maintenance of your Wacker Neuson machine. In the interest of your 
own safety and to prevent accidents, you should carefully read through the safety 
information, familiarize yourself with it and observe it at all times.

This operator's manual is not a manual for extensive maintenance and repair 
work. Such work should be carried out by Wacker Neuson service or authorized 
specialists.

The safety of the operator was one of the most important aspects taken into con-
sideration when this machine was designed. Nevertheless, improper use or in-
correct maintenance can pose a risk. Please operate and maintain your Wacker 
Neuson machine in accordance with the instructions in this operator's manual. 
Your reward will be troublefree operation and a high degree of availability.

Defective machine parts must be replaced immediately!

Please contact your Wacker Neuson representative if you have any questions 
concerning operation or maintenance.

All rights reserved, especially reproduction and distribution rights.

Copyright 2015 Wacker Neuson Produktion GmbH & Co. KG 

No part of this publication may be reproduced in any form or by any means, elec-
tronic or mechanical, including photocopying, without the expressed written per-
mission of Wacker Neuson.

Any type of reproduction, distribution or storage on data media of any type and 
form not authorized by Wacker Neuson represents an infringement of copyright 
and will be prosecuted. 

We expressly reserve the right to make technical modifications – even without 
special notice – which aim at further improving our machines or their safety stan-
dards.

Summary of Contents for DPU 4545





























































































Reviews: