Wabtec Ricon K Series Service Manual Download

Page: 60 / 79

4 - 11

SPARE PARTS

SEPTEMBER 2010

32DSKE02.B.1

S/K-SERIES EXPORT USE SERVICE MANUAL

FIGURE 4-6: S/K-SERIES ELECTRICAL ASSY

FIG.

ITEM DESCRIPTION

QTY CONFIG. PART

NO.

BRACKET WLDT, PUMP CHASSIS

44978

HARNESS, PUMP CHASSIS, 12V

45219

COUNTER ASSY, 12V, MODULAR

38391

SCREW, PHP, 6-32 X 1/4, TYPE F, SST

REF

21953

KIT, GROUND STRAP, LONG

37388

KIT, SOLENOID, 12V, SGL POLE, SGL THROW

29297

SCREW, HEX, 10-24 X 3/8, QUICK-DRIVE

37702

KIT, BLOCK, POSITIVE CONNECTION, MODULAR

35454

BUSBAR, 1.45" W

37767

BUMPER, CHASSIS

44883

CIRCUIT BREAKER, 8AMP, RED

265108

CIRCUIT BREAKER, 30AMP, WHITE

26510

NUT, PANEL, 7/16-28 UNEF

37779

RELAY, 12V COIL 40A QUICK CONNECT

28-36-405

BRACKET, PUMP CHASSIS

42986

SCREW

21953

KIT, SWITCH ASSY, POSITION INPUT

44236

KIT, SWITCH BLOCK/MICROSWITCH W/HARDWARE

44237

SWITCH, LIMIT, UPPER/LOWER, (MODIFIED)

V2-ES-110

CAM, POSITION INPUT

45200

ACTUATOR, FOLD CUTOFF

V2-AC-089

SCREW, PHP, 10-24 X 2 1/4

10860

SPRING, ADJUSTABLE LIMIT SWITCH

V2-ES-93

KIT, BUZZER WITH BRACKET

44238

BUZZER ALARM, 90dB@30cm/12VDC

45209

26 *

100 AMP MEGA FUSE (LITTLEFUSE) (REF FIG 2-10)

70017

27 *

MEGA FUSE HOLDER (REF FIG 2-10)

70018

NOTE

: (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts.

NOTE

: * Item or configuration not shown.

Summary of Contents for Ricon K Series
















































































Search results

Summary of Contents for Ricon K Series

Reviews:

Related manuals for Ricon K Series

Brands by name

Popular brands

Wabtec Ricon K Series, Service Manual

Search results

Summary of Contents for Ricon K Series

Reviews:

Related manuals for Ricon K Series

Brands by name

Popular brands