manualshive.com logo in svg

Wabtec Ricon K Series, Service Manual

Share
Download
Wabtec Ricon K Series Service Manual Download Page 68

 

 

4 - 19 

SPARE PARTS

SEPTEMBER 2010 

32DSKE02.B.1 

S/K-SERIES EXPORT USE SERVICE MANUAL 

 

FIGURE 4-8:  S-SERIES SOLID PLATFORM ASSY 

FIG.  

 

 

 

ITEM DESCRIPTION 

QTY CONFIG. PART 

NO. 

 1     

PLATFORM WLDT, SOLID (32" X 51") SILVER 

REF 

S2005 

V2-PH-089S 

 2     

BUMPER, UHMW, .75D X .38T 

  2 

   

V2-AC-027 

  

ATTACHING 

PARTS 

 3     

SCREW, PHP, 8 TEK X 1/2 (BAG OF 10) 

  1 

   

15961 

 4     

ROLLSTOP ASSY, 6"H X 32"W 

REF 

   

39952 

  

  ATTACHING 

PARTS 

 5     

PIN, CLEVIS 5/16 X 1-1/4 (BAG OF 10) 

  1 

   

19513 

 6     

KIT, ACTUATOR WLDT, ROLLSTOP, LH 

  1 

   

44211 

 7     

KIT, ACTUATOR WLDT, ROLLSTOP, RH 

  1 

   

44210 

 8     

KIT, HARDWARE, ROLLSTOPS 

  1 

   

110011 

 9     

KIT, COLLAR ROLLSTOP ACTUATOR, 6.25", W/HARDWARE 

  1 

   

28775 

 9A *  

KIT, COLLAR ROLLSTOP ACTUATOR, 8.25", W/HARDWARE 

  1 

   

28773 

10     

KIT, FLANGE BEARING 1"ID (BAG OF 10) 

  1 

   

19579 

11     

BLOCK, GREY, PLATFORM LEVEL ADJ 

  2 

   

VT-AH-142S 

12     

SCREW, HSS, 1/2-20 X 1 1/4 W/NYLOK (BAG OF 10) 

  1 

   

19704 

 

13     

KIT, HINGE, PLATFORM W/HARDWARE 

  1 

   

44212 

14   

SPRING, BRIDGEPLATE 

 3 

   

25463 

15     

ROLLSTOP WLDT, INNER, 32" (YELLOW WRINKLE) 

REF 

   

32443 

16     

BLOCK, BASE LATCH, RATCHET 

  1 

   

36576 

17     

KIT, SPACER, BRIDGEPLATE 

  2 

   

42038 

18     

SENSOR ASSY, ROLLSTOP 

  2 

   

32755 

19     

HARNESS, SKI SWITCH, EXTENSION 

  2 

   

37340 

20  ** 

KIT, SKI WHEEL, ROLLSTOP, EXPORT 

  2 

S2005 

42951 

21   

SPRING, TORSION (LH)  

1 

 

 

V2-SP-021 

22     

SPRING, TORSION (RH) 

  1 

   

V2-SP-022 

NOTE

:  (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. 

NOTE

:  * 

Item or configuration not shown. 

NOTE

:  **  Item optional. 

 

 

Summary of Contents for Ricon K Series
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands