manualshive.com logo in svg

Wabtec Ricon K Series, Service Manual

Share
Download
Wabtec Ricon K Series Service Manual Download Page 26

 

 

2 - 13

32DSKE02.B.1 

INSTALLATION

SEPTEMEBER 2010 

S/K-SERIES EXPORT USE SERVICE MANUAL 

 

FIGURE 2-16:  LIMIT SWITCH ADJUSTMENT CLEARANCE 

k.  Cycle platform through all functions (DEPLOY, DOWN, UP, and STOW) to verify correct adjustment.  Refer 

to 

Table 2-1

 if necessary. 

TABLE 2-1:  LIMIT SWITCH ADJUSTMENT CHART  

COMPONENT

 

SYMPTOM

 

CORRECTIVE 

ACTION

 

ADJUSTMENT PROCEDURE

 

Fold cutoff  
actuator

 

Lift does not 
fold tightly.

 

Rotate CAM 
(CCW).

 

With lift fully folded (handrails should be 
folded tight against vertical arms), rotate 
actuator so that it barely trips fold cutoff 
switch.

 

 

Pump runs 
continuously.

 

Rotate actuator 
(CW).

 

Test lift.  Pump should cutoff when lift is 
folded tight.

 

Up cutoff  
adjustment 
screw

 

Lift stops 
low.

 

Adjust screw 
(CW).

 

Adjust up cutoff switch so that lift stops just 
before first knuckle actuator saddle or roller 
touches underside of lower parallel arm.  
(Saddle or roller should be about 3mm  
(1/8 in.) from lower parallel arm.)

 

 

Lift stops 
high.

 

Adjust screw 
(CCW).

 

 

Deploy cutoff  
adjustment 
screw

 

Lift stops 
low.

 

Adjust screw 
(CCW).

 

Adjust deploy limit switch so that lift stops 
just below “Up” cutoff described in above 
step.  This will give the necessary overlap 
to avoid “dead” spots.

 

 

Lift stops 
high.

 

Adjust screw 
(CW).

 

 

END OF TABLE

 

 

Summary of Contents for Ricon K Series
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands