manualshive.com logo in svg

Wabtec Ricon K Series, Service Manual

Share
Download
Wabtec Ricon K Series Service Manual Download Page 72

 

 

4 - 23 

SPARE PARTS

SEPTEMBER 2010 

32DSKE02.B.1 

S/K-SERIES EXPORT USE SERVICE MANUAL 

 

FIGURE 4-10:  K-SERIES PLATFORM ASSY 

FIG.  

 

 

 

ITEM DESCRIPTION 

QTY CONFIG. PART 

NO. 

 1     

PLATFORM WLDT, FLDG, 30" X 44" (SILVER) 

REF 

K1200 

22500S 

 1A *  

PLATFORM WLDT, FLDG, 30" X 51" (SILVER) 

REF 

K2003 

22501S 

 1B *  

PLATFORM WLDT, FLDG, 32" X 51" (SILVER) 

REF 

K2005 

22502S 

 2     

BUMPER, UHMW, .75D X .38T 

  2 

   

V2-AC-027 

  

ATTACHING 

PARTS 

 3     

SCREW, PHP, 8 TEK X 1/2 (BAG OF 10) 

  1 

   

15961 

 4     

ROLLSTOP ASSY, 6"H X 30"W, MODULAR 

REF 

K1200 

39951 

  

   

REF  K2003  39951 

 4A *  

ROLLSTOP ASSY, 6"H X 32"W 

REF 

K2005 

39952 

  

  ATTACHING 

PARTS 

 

1 

 

 

V2-FL-93 

 5     

KIT, ACTUATOR WLDT, ROLLSTOP, LH 

  1 

   

44211 

 6     

KIT, ACTUATOR WLDT, ROLLSTOP, RH 

  1 

   

44210 

 7     

KIT, HARDWARE, ROLLSTOPS 

  1 

   

110011 

 8     

KIT, COLLAR ROLLSTOP ACTUATOR, 6.25", W/HARDWARE 

  1 

   

28775 

 8A *  

KIT, COLLAR ROLLSTOP ACTUATOR, 8.25", W/HARDWARE 

  1 

   

28773 

 9     

KIT, FLANGE BEARING 1"ID (BAG OF 10) 

  1 

   

19579 

10     

BLOCK, GREY, PLATFORM LEVEL ADJ 

  2 

   

VT-AH-142S 

11     

SCREW, HSS, 1/2-20 X 1 1/4 W/NYLOK 

  2 

   

14403 

 

12     

KIT, HINGE, PLATFORM W/HARDWARE 

  1 

   

44212 

13   

SPRING, BRIDGEPLATE 

 3 

   

25463 

14     

ROLLSTOP WLDT, INNER, 30" PLATFORM 

REF 

K1200 

32463 

  

   

REF  K2003 

14A  * 

ROLLSTOP WLDT, INNER, 32" (YELLOW WRINKLE) 

REF 

K2005 

32443 

15     

BLOCK, BASE LATCH, RATCHET 

  1 

   

36576 

16     

KIT, SPACER, BRIDGEPLATE 

  2 

   

42038 

17     

KIT, LINK ASSY 44”, (LH) FRONT & REAR, YELLOW 

  1 

   

44255 

17A  * 

KIT, LINK ASSY 51”, (LH) FRONT & REAR, YELLOW 

  1 

   

44257 

17B  * 

KIT, LINK ASSY 54”, (LH) FRONT & REAR, YELLOW 

  1 

   

44264 

18     

KIT, LINK ASSY 44”, (RH) FRONT & REAR, YELLOW 

  1 

   

44256 

18A  * 

KIT, LINK ASSY 51”, (RH) FRONT & REAR, YELLOW 

  1 

   

44263 

18B  * 

KIT, LINK ASSY 54”, (RH) FRONT & REAR, YELLOW 

  1 

   

44265 

19     

SENSOR ASSY, ROLLSTOP 

  2 

   

32755 

20     

HARNESS, SKI SWITCH, EXTENSION 

  2 

   

37340 

21  ** 

KIT, SKI WHEEL, ROLLSTOP, EXPORT 

  2 

   

42951 

22   

SPRING, TORSION (LH)  

1 

 

 

V2-SP-021 

23     

SPRING, TORSION (RH) 

  1 

   

V2-SP-022 

NOTE

:  (REF) in QTY column is for Referenced Parts Only and are not sold as spare parts. 

NOTE

:  *  Item or configuration not shown. 

NOTE

:  **  Item optional. 

Summary of Contents for Ricon K Series
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands