WABCO SMARTTRAC MM1543 Maintenance Manual Download Page 54

Page: 54 / 72

Appendix I

SPN

Component

FMI Fault Description

Repair

1043

Pressure

sensor

reference

voltage

Internal sensor

failure

• Reset the ECU by cycling the ignition or by using the reset

option in the TOOLBOX™ Software.

• If the fault persists, check the ABS ECU powers and

grounds.

• After checking powers and grounds, if the fault still persists,

it may indicate the unit has failed.

1044

Pump motor

Pump motor voltage

supply problem

• Reset the ECU by cycling the ignition or by using the reset

option in the TOOLBOX™ Software.

• If the fault persists, check the ABS ECU powers and

grounds.

• After checking powers and grounds, if the fault still persists,

it may indicate the unit has failed.

Pump motor voltage

supply problem

Pump motor

defective, high

current consumption

Pump motor or pump

mechanical problem

1049

Pressure

sensor 1

Internal sensor

failure

• Reset the ECU by cycling the ignition or by using the reset

option in the TOOLBOX™ Software.

• If the fault persists, check the ABS ECU powers and

grounds.

• After checking powers and grounds, if the fault still persists,

it may indicate the unit has failed.

10
2

1052

Pressure

sensor 2

Internal sensor

failure

• Reset the ECU by cycling the ignition or by using the reset

option in the TOOLBOX™ Software.

• If the fault persists, check the ABS ECU powers and

grounds.

• After checking powers and grounds, if the fault still persists,

it may indicate the unit has failed.

1079

Sensor

supply

voltage

Internal power

supply failure

• Reset the ECU by cycling the ignition or by using the reset

option in the TOOLBOX™ Software.

• If the fault persists, check the ABS ECU powers and

grounds.

• After checking powers and grounds, if fault still persists, it

may indicate the unit has failed.

1080

Wheel speed

sensor

supply

voltage

Internal power

supply failure

• Reset the ECU by cycling the ignition or by using the reset

option in the TOOLBOX™ Software.

• If the fault persists, check the ABS ECU powers and

grounds.

• After checking powers and grounds, if the fault still persists,

it may indicate the unit has failed.

Summary of Contents for SMARTTRAC MM1543









































































Search results

Summary of Contents for SMARTTRAC MM1543

Reviews:

Related manuals for SMARTTRAC MM1543

Brands by name

Popular brands

WABCO SMARTTRAC MM1543, Maintenance Manual

Search results

Summary of Contents for SMARTTRAC MM1543

Reviews:

Related manuals for SMARTTRAC MM1543

Brands by name

Popular brands