WABCO SMARTTRAC MM1543 Maintenance Manual Download Page 68

Page: 68 / 72

Appendix II

The order will be processed and a link to download the configuration file will be displayed. Click the

hyperlink to download the configuration file.

4013311a

The file extension “.HY” is specifically for the SmartTrac™ hydraulic ABS module only.

Ensure the file has this. No other file will be compatible.

IMPORTANT: The configuration file will be available in your account for seven days from

purchase. The configuration file must be downloaded to a computer within that time.

The following message will be displayed regarding recommended file storage location. Press OK to

continue with saving the file.

4013312a

Save the configuration file to a location that can be accessed while connected to the vehicle.

The aftermarket programming application will allow the file selection from any location in your

computer. (Not just the AMProg Folder.)

4013312a

Summary of Contents for SMARTTRAC MM1543









































































Search results

Summary of Contents for SMARTTRAC MM1543

Reviews:

Related manuals for SMARTTRAC MM1543

Brands by name

Popular brands

WABCO SMARTTRAC MM1543, Maintenance Manual

Search results

Summary of Contents for SMARTTRAC MM1543

Reviews:

Related manuals for SMARTTRAC MM1543

Brands by name

Popular brands