manualshive.com logo in svg

WABCO OPTIFLOW SIDEWINGS, Installation Manual

Share
Download
WABCO OPTIFLOW SIDEWINGS Installation Manual Download Page 31

31

OptiFlow™ SideWings

Installation

5.7 

Installation of Flow Conductors

 

!

The distance between the outer sides of the tires and the SideWing 
components should not be less than 30mm.

The assembly tolerances are +/- 3mm.

Check if the crank storage position on the vehicle frame needs to be 
changed. With some confi gurations, you can request a crank of a different 
length. 
Mount the Flow Conductor so the landing legs can be operated easily when 
the Flow Conductor is open.

5.7.1 Flow Conductor Rotational

 

– Depending on your BOM (Bill Of Material) please check if you have this 

part or not.

 

!

The position of Flow Conductor Rotational must be chosen very carefully. 
There is no fl exibility in the positioning after installation.

  

–

– Install rubber on Flow Conductor before installing on trailer.

Install rubber on Flow Conductor before installing on trailer.

For OEM (Original Equipment Manufacturer) installation the top rubber may 
be supplied separately.

Summary of Contents for OPTIFLOW SIDEWINGS
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands