Volvo Penta TAD734GE Manual Download

Page: 60 / 64

Lubrication System

Oil

Oil capacity including oil filters, approx.:

35litre (9.25 US gal)

Oil pressure, hot engine:

at operating speed

300-600 kPa (44–87 psi)

Oil pressure during neutral

270 kPa

Oil filter

Full flow filter

By-pass filter

Lube Oil Pump

Type

Gear driven

Oil recommendations

Oil grade

Sulfur content in fuel, by weight

up to 0,5 %

0,5 – 1,0 %

more than 1,0 %

Oil change interval: Reached first in operation:

VDS-3
VDS-2

600

hrs / 12 month

300

hrs / 12 month

150

hrs / 12 month

NOTICE!

Mineral based oil, as well as fully or semi-synthetic, can be used on condition that it complies with

thequality requirements above.

1) If sulfur content is > 1.0 % by weight, use oil with TBN > 15.

2) The oil must also comply with at least one of the following specifications ACEA:E7, ACEA:E5, Global DHD-1, API:CI-4 or API:CH-4.

VDS = Volvo Drain Specification
ACEA = Association des Constructeurs Européenne d’Automobiles
API = American Petroleum Institute Global
DHD = Global Diesel Heavy Duty
TBN = Total Base Number

Viscosity

Select the viscosity according to the table.

The temperature values refer to stable ambient tem-
peratures.

* SAE 5W/30 refers to synthetic or semi-synthetic oils.

Technical Data

47702660 03-2013 © AB VOLVO PENTA

Summary of Contents for TAD734GE

































































Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands

Volvo Penta TAD734GE, Manual

Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands