Volvo Penta TAD734GE Manual Download

Page: 62 / 64

Cooling System

Type

Pressurized, sealed

Pressure cap, max. opening pressure

75 kPa (10.88 PSI)

Coolant quantity (engine):

17 liter (4.49 US gallon)

Coolant quantity (engine, radiator and hoses):

41liter (10.8 US gallon)

Thermostat, quantity

1 pc.

Thermostat, opening temperature:

82 °C (179.6 °F)

Coolant

Volvo Penta Coolant VCS and VCS Ready Mixed (yel-
low colour) are based on Organic Acid Technology,
OAT.

Volvo Penta Coolant and Coolant Ready Mixed (green
colour) are silicate based.

Water Quality

ASTM D4985:

Total solid particles

<340 ppm

Total hardness

<9,5° dH

Chloride

<40 ppm

Sulfate

<100 ppm

pH value

5.5–9

Silica (acc. ASTM D859)

<20 mg SiO

Iron (acc. ASTM D1068)

<0.10 ppm

Manganese (acc. ASTM D858)

<0.05 ppm

Conductivity (acc. ASTM D1125)

<500 µS/cm

Organic content, COD

(acc.

ISO8467)

<15 mg KMnO

coolant vcs ready mixed

P0013077

P0002094

Technical Data

47702660 03-2013 © AB VOLVO PENTA

Summary of Contents for TAD734GE

































































Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands

Volvo Penta TAD734GE, Manual

Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands