Volvo Penta TAD734GE Manual Download

Page: 32 / 64

Fault Code Register

Fault code, engine

SPN

PID

PPID

SID

PSID

Flash code

Electrical
fault/Value
fault

FMI

Coolant Water Pressure

Percent Accelerator Pedal Position

2.7/- (EMS)
2.8/- (CIU)

Fuel delivery pressure

Maintenance page 49

3.6/3.8

1, 3, 5, 7

Water in fuel indicator

Draining condensate, fuel system page 51

2.9/2.1

0, 3, 4

Engine Oil Level

Oil level, checking and topping
up page 47

5.9/5.7

1, 3, 4, 5

Engine oil filter diff pressure

Engine Oil Pressure

Oil level, checking and topping
up page 47

100

3.1/6.6

1, 3, 5, 18

Boost pressure

102

0, 3, 5, 16

Boost Temperature

105

3.2/6.2

0, 4, 5, 16

Boost pressure

106

3.4/3.5

0, 3, 5, 16

Air filter pressure

107

5.5/5.5

0, 3, 4, 5

Ambient air pressure

108

-/-

2, 3, 4

Coolant Temperature

Coolant Level, Checking and Topping
Up page 54

110

3.3/6.1

0, 4, 5, 16

Coolant Level

Coolant Level, Checking and Topping
Up page 54

111

2.3/2.2

1, 3, 5

Crankcase Pressure

153

7.8/7.7

0, 2, 3, 5

Battery Voltage

Battery, Charging page 60

158

-/3.9 (EMS)
-/6.9 (CIU)

1, 3, 4

Injection control pressure

164

8.3

2, 4, 5

Ambient Air Temperature Sensor

171

Ambient Air Temperature Sensor

172

7.9/-

4, 5

Engine Oil Temperature

Oil level, checking and topping
up page 47

175

3.7/5.8

0, 4, 5, 16

Engine Speed

190

-/2.6

0, 16

Throttle position

608

-/-

Throttle calibrated position

608

132

2.8/-

SAE J1708 Data Link

608

250

9.2/-

SAE J1939 Data Link

608

201

+5V sensor supply

620

232

9.3/-

3, 4

Inlet Air Temperature

626

5.4/-

3, 4, 5

Program memory

628

240

9.9/-

2, 12

Controller error

629

254

9.9/- (EMS)
9.8/- (CIU)

8, 12

47702660 03-2013 © AB VOLVO PENTA

Summary of Contents for TAD734GE

































































Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands

Volvo Penta TAD734GE, Manual

Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands