Volvo Penta TAD734GE Manual Download

Page: 11 / 64

Display setting

settings for the display. Adjustment is made with the

and

buttons; see DCU panel illustration.

•

Set contrast (%)

- contrast setting.

•

Set backlight time (sec)

- time setting (in seconds)

for display backlighting on, lighting is then shut off if
the panel is not used.

•

Set backlight brightness

- display backlighting

brightness setting.

Information

shows the data for the engine and DCU.

•

Engine hardware Id

- engine control unit part num-

ber.

•

Engine software Id

- engine control unit software

part number.

•

Engine dataset1 Id

- engine data set 1 part number.

•

Engine dataset2 Id

- engine data set 2 part number.

•

Vehicle Id

- chassis number.

•

DCU hardware Id

- DCU part number.

•

DCU software Id

- DCU software part number.

•

DCU dataset1 Id

- DCU data set 1 part number.

•

DCU dataset2 Id

- DCU data set 2 part number.

Instruments and Controls

47702660 03-2013 © AB VOLVO PENTA

Summary of Contents for TAD734GE

































































Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands

Volvo Penta TAD734GE, Manual

Search results

Summary of Contents for TAD734GE

Reviews:

Related manuals for TAD734GE

Brands by name

Popular brands