manualshive.com logo in svg

Volvo Penta TAD420VE, Workshop Manual

Share
Download
Volvo Penta TAD420VE Workshop Manual Download Page 83

Technical Data: TD/TAD720-722, TAD730/733, TAD750/760

81

Group 20

Cooling system

Type ...................................................................... Pressurized, closed circuit
Pressure valve opens at:

TD720GE/TAD720GE, TAD730/731GE: ............ 60 kPa

(13 psi)

TAD721GE/TAD722GE
TD720VE/TAD720VE/TAD721VE,
TAD732-733GE, max

1)

: ...................................... 90 kPa

(13 psi)

1)

Versatile engines are not equipped with a pressure valve from factory

Capacity (engine):. ................................................. 9.8 liters

(2.59 US gal)

Capacity (engine and cooler):

TD720GE: ........................................................... 22 liters

(5.8 US gal)

TAD720GE/TAD730/731GE: ............................... 23.8 liters

(6.3 US gal)

TAD721GE/TAD722GE/TAD732/733GE: ............ 27.3

(7.2 US gal)

Thermostat

Type: ..................................................................... Piston thermostat
Begins to open at

TD720GE/TAD720GE/TD720VE/TAD730/731GE: 83°C

(181°F)

TAD721GE/TAD722GE/TAD720VE/TAD721VE
TAD722VE/TAD750VE/TAD760VE,
TAD732/733GE: ................................................. 87° C

(189° F)

Fully open at

TD720GE/TAD720GE/TD720VE: ....................... 95°C

(203°F)

TAD721GE/TAD722GE/TAD720VE/TAD721VE
TAD722VE/TAD750VE/TAD760VE: ................... 102° C

(216° F)

Coolant pump

Type ...................................................................... Belt-driven centrifugal pump

Glycol (Antifreeze)

Volvo Penta glycol (antifreeze) mixed 45/55 with clean water

Anti-corrosion agent

Used only in markets where there is no risk of freezing, mixed with water

3)

.

3)

The anti-corrosion agent must not be mixed with glycol or other types of anti-corrosion fluid as this could result in negative
consequences.

Water quality specification:

To avoid the risk of clogging in the cooling system, the coolant should be mixed with pure water to ASTM D4985.
If any doubt about the purity of the water, distilled water or ready-mixed coolant should always be used instead

TD/TAD720-722:

1. Coolan connection (inlet)
2. Thermastat housing
3. Coolant pump
4. Lubrication oil cooler
5. Cylinder cooling
6. Cylinder head cooling
7. Coolant connection (outlet)

Summary of Contents for TAD420VE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands