manualshive.com logo in svg

Volvo Penta TAD420VE, Workshop Manual

Share
Download
Volvo Penta TAD420VE Workshop Manual Download Page 34

Technical data: TD/TAD420VE, TAD620VE, TAD650VE, TAD660VE

32

Group 20

Intake and exhaust system

Turbocharger

Make and designation ............................................ Schwitzer S200
Boost pressure at rated speed

1)

, ±10 %:

TD420VE ............................................................ 105 kPa

(15.2 psi)

TAD420VE .......................................................... 143 kPa

(20.7 psi)

TAD620VE,TAD650VE,TAD660VE ..................... 155 kPa

(22.5 psi)

Lube system .......................................................... Pressure lubrication
Max, permitted radial clearance

(compressor side) ............................................... 0.88 mm

(0.0346")

Max, permitted axial clearance .............................. 0.1 mm

(0.0039")

Max allowed back pressure in exhaust line ............ 7.5 kPa

(0.9 psi)

Exhaust gas temperatur

, approx:

At engine speed

1)

: ..................................................

1800 rpm

2100 rpm

2300 rpm

2500 rpm

TD420VE ............................................................ 555°C

540°C

540°C

540°C

(1031°F)

(1004°F)

(1004°F)

(1004°F)

TAD420VE .......................................................... 490°C

470°C

475°C

475°C

(914°F)

(878°F)

(887°F)

(887°F)

TAD620VE,TAD650VE,TAD660VE ..................... 485°C

465°C

460°C

455°C

(905°F)

(869°F)

(860°F)

(851°F)

1)

 

See General information, Power standards.

Cooling system

Type ...................................................................... Pressurized, closed

Pressure valve opens at max

2)

............................ 90 kPa

(13 psi)

2)

 Versatile engines are not equipped with a pressure valve from factory

Capacity, engine:

TD420VE/TAD420VE .......................................... 4.7 liters

(1.24 US gal)

TAD620VE,TAD650VE,TAD660VE ..................... 6 liters

(1.58 US gal)

Thermostat:

Type ...................................................................... One piston thermostat
Begins to open at ................................................... 83°C

(181°F)

Fully open at .......................................................... 95°C

(203°F)

Coolant pump:

Type ...................................................................... Belt-driven centrifugal pump

Glycol (Antifreeze)

Volvo Penta glycol (antifreeze) mixed 45/55 with clean water

Anti-corrosion agent

Used only in markets where there is no risk of freezing, mixed with water

3)

.

3)

 The anti-corrosion agent must not be mixed with glycol or other types of anti-corrosion fluid as this could result in negative consequences.

Water quality specification:

To avoid the risk of clogging in the cooling system, the coolant should be mixed with pure water to ASTM D4985.
If any doubt about the purity of the water, distilled water or ready-mixed coolant should always be used instead.

Air intake

Air intake restriction, clean filter ............................. 2.5 kPa

(0.3 psi)

Max allowed air intake restriction ........................... 6.5 kPa

(0.9 psi)

Summary of Contents for TAD420VE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands