manualshive.com logo in svg

Volvo Penta TAD420VE, Workshop Manual

Share
Download
Volvo Penta TAD420VE Workshop Manual Download Page 72

Technical Data: TD/TAD720-722, TAD730/733, TAD750/760

70

Group 20

Viscosity

The viscosity should be selected from the adjacent
table.

NOTE! 

the temperatures refer to constant outside air

temperature. The tabell above refers to synthetic or
synthetic-based oil.

Lubricating system

Sulfur content in fuel, by weight

Engine

Oilgrade

2)

< 0,5 %

0,5 – 1,0 %

> 1,0 %

1)

Oil change interval, reached first in operation

T(A)D720-721VE

VDS-3

500 

h / 12 months

250 

h / 12 months

125 

h / 12 months

T(A)D720GE

VDS-2

TAD730/731GE,

ACEA: E7, E5, E3

TAD721/722GE,

API: CI-4, CH-4, CG-4

TAD732/TAD733GE,
TAD750/760VE, open
crankcase ventilation

TAD721/722GE,

ACEA: E4

500 

h / 12 months

250 

h / 12 months

125 

h / 12 months

TAD732/733GE,

API: CI-4, CH-4

TAD750/760VE, closed

NOTE!

 Fully synthetic oil must be used

crankcase ventilation

TAD722VE

ACEA: E4

power<200kW

500 

h / 12 months

250 

h / 12 months

125 

h / 12 months

power>200kW

250 

h / 12 months

125 

h / 12 months

60 

h / 12 months

1) 

If the sulfur content is > 1.0% by weight, use oil with TBN > 15 

closed crankcase ventilation

2) 

 For markets outside Europe, API: CG-4 and CH-4 can be used instead of ACEA: E3.

NOTE! 

Mineral based oil, either fully or semi-synthetic, can be used on condition that it complies with the quality

requirements above.

NOTE!

 For 6 and 7-liter engines equipped with low profile type oil pans, the oil change interval must be halved.

VDS = Volvo Drain Specification
ACEA = Association des Constructeurs Européenne d’Automobiles
API = American Petroleum Institute
Global DHD = Global Diesel Heavy Duty
TBN = Total Base Number

Summary of Contents for TAD420VE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands