manualshive.com logo in svg

Volvo Penta TAD420VE, Workshop Manual

Share
Download
Volvo Penta TAD420VE Workshop Manual Download Page 78

Technical Data: TD/TAD720-722, TAD730/733, TAD750/760

76

Group 20

Commencement of delivery (FB)  720–733

The engine is equipped with a separate injection pump for each cylinder.
This means that the commencement of delivery (

FB

), when necessary, has

to be adjusted separate for each pump unit. The commencement of delive-
ry (

FB

) is adjusted with a shim, placed between lifter and injection pump.

For exchange of injection pump without any parts of vital importance has
been replaced, see chapter ”

EP code

”. For renovation or when any parts of

vital importance have been replaced, special tools (999 8685 and 999 8679)
must be used, to be able to calculate the thickness for the new shim.
The value for commencement of delivery and camshaft type is indicated on
the identification plate, see ”

General information”, ”Identification plate

”.

When calculating the shim thickness, apply a mathematical formula, see
”

Theoretical thickness for shim”, 

where some values are from table 1

and other are measured on the engine. For complete instruction, see

”Workshop Manual”.

FB

(Commencement of

delivery)

Camshaft

types

Vh

Pre-stroke

Vh

corr.factor

Pre-stroke

correction factor

 Lo

Basic dimension

Injection pump

Table 1 (Commencement of delivery)

All measurements are in mm (1 mm = 0.0394")

Summary of Contents for TAD420VE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands