manualshive.com logo in svg

Volvo Penta TAD420VE, Workshop Manual

Share
Download
Volvo Penta TAD420VE Workshop Manual Download Page 39

Technical Data: TD/TAD520, TAD530/531/532

37

Group 20

Type: .................................................................... Wet, replaceable
Number of seals per liner: ..................................... 2
Bore: ..................................................................... 108

+0.02

 

mm

(4.252"

+0.0008"

)

Max bore wear: ..................................................... 108.1 mm

(4.256")

Height sealing surface 

(A)

: .................................... 9

-0.02

 mm

(0.3543"

-0.0008"

)

Liner collar seating depth in block: ........................ 8.92

+0.03

 mm

(0,3512"

+0.0012"

)

Projection of liner above block surface: ................. 0.03 – 0.08 mm (0.0012" – 0.0031")

A

Cylinder liners

TD520GE/TAD520GE

TD520VE/TAD520VE

TAD530/531/532GE

Engine block

Cylinder head

Type: ........................................ Common cylinder head
Max surface unevenness: ......... 0.085 mm

(0.00335")

Cylinder head bolts

Thread size: .............................. M 14
Quantity and length: .................. 18 x 141 mm

( 18 x 5.55")

1)

 See engine plate for specifications.

2)

 Weight according to DIN 70020-A

3)

 Extra weight TAD520GE SAE 2 (1800 rpm) 36 kg (80 lb)

4)

 Including clutch and frame

General

Type designation ..............................................
Direction of rotation (seen from flywheel)
No. of cylinders ................................................
Cylinder bore mm (inch) ...................................
Stroke mm (inch) .............................................
Cylinder volume liter

 

(inch 

3 

) .............................

No. of valves ....................................................
 Compression ratio:

EPA1 ............................................................
EPA2 ............................................................
EU2 ..............................................................

Injection sequence ...........................................
Engine power:

At 1500 rpm kW (hp) .....................................
At 1800 rpm kW (hp) .....................................

Torque Nm (lbf.ft) .............................................

At engine speed rpm .....................................

Torque Nm (lbf.ft) .............................................

At engine speed rpm .....................................

Low idle rpm .....................................................
Highest full load speed rpm ..............................
Weight, dry (lb) .................................................
Gross weight, dry (lb)

TAD531GE

Anti- clockwise
4
108 (4.25”)
130 (5.12”)
4.76 (290)
8

18.0:1
1-3-4-2

102 (139)

1)

110 (150)

1)

649 (479)
1500
584 (430)
1800
800 – 950
1500/1800 

1)

575 (1268) 

2,3)

606 (1336) 

2,3)

TAD530GE

Anti- clockwise
4
108 (4.25”)
130 (5.12”)
4.76 (290)
8

18.0:1
1-3-4-2

89 (139)

1)

95 (150)

1)

567 (479)
1500
504 (430)
1800
800 – 950
1500/1800 

1)

575 (1268) 

2,3)

606 (1336) 

2,3)

TAD532GE

Anti- clockwise
4
108 (4.25”)
130 (5.12”)
4.76 (290)
8

18.0:1

1-3-4-2

129 (139)

1)

136 (150)

1)

821 (479)
1500
722 (430)
1800
800 – 950
1500/1800 

1)

575 (1268) 

2,3)

606 (1336) 

2,3)

Replacable, wet

Summary of Contents for TAD420VE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands