manualshive.com logo in svg

Volvo Penta TAD420VE, Workshop Manual

Share
Download
Volvo Penta TAD420VE Workshop Manual Download Page 24

Technical data: TD/TAD420VE, TAD620VE, TAD650VE, TAD660VE

22

Group 20

Viscosity

The viscosity should be selected from the adjacent
table.

NOTE! 

the temperatures refer to constant outside air

temperature. The tabell above refers to synthetic or
synthetic-based oil.

Fuel sulfur content in percent by weight

Lubricating system

Up to 0.5 %

0.5 – 1 %

More than 1 %

1)

Oil change interval: In operation whichever reached first

Oil grade

2)

VDS-3, VDS-2
ACEA: E7, E5, E3

500

 hours or 12 months

250

 hours or 12 months

125

 hours or 12 months

API: CI-4, CH-4, CG-4

1) 

If the sulfur content is > 1.0% by weight, use oil with TBN > 15

2)

 For markets outside Europe, API: CG-4 and CH-4 can be used instead of ACEA: E3.

NOTE! 

Mineral based oil, either fully or semi-synthetic, can be used on condition that it complies with the quality

requirements above.

NOTE!

 For 6 and 7-liter engines equipped with low profile type oil pans, the oil change interval must be halved.

VDS = Volvo Drain Specification
ACEA = Association des Constructeurs Européenne d’Automobiles
API = American Petroleum Institute
Global DHD = Global Diesel Heavy Duty
TBN = Total Base Number

Summary of Contents for TAD420VE





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands