VKI Technologies CAFFE MIO Operation & Service Manual Download Page 74

Page: 74 / 110

S E C T I O N 5 – R E P L A C I N G C O M P O N E N T S

CAFFÈ MIO – OPERATION AND SERVICE

Page 74 of 110

R e p l a c i n g M a j o r C o m p o n e n t s

Ingredient Dispenser Motor

With machine power OFF, open the front door and open the machine lid.

Remove the brewer.

Refer to the "

Replacing the Brewer

" instructions in this manual.

Remove the brewer bracket.

Refer to the "

Replacing the Brewer Bracket

" instructions in this manual.

Remove the spill plate that surrounds the two dispensers.

Remove the screws at the front and rear of the spill plate securing it to the top of the machine.

Remove the lids on both of the dispensers.

Slide the spill plate up and over the dispensers to remove it.

Rotate both ingredient dispenser spouts upwards.

Remove the screw securing the front of each dispenser to the dispenser base.

Spill Plate

Remove Screw

Spill Plate and Dispenser

Lids Removed

Remove Lid

Remove

Summary of Contents for CAFFE MIO















































































































Search results

Summary of Contents for CAFFE MIO

Reviews:

Related manuals for CAFFE MIO

Brands by name

Popular brands

VKI Technologies CAFFE MIO, Operation & Service Manual

Search results

Summary of Contents for CAFFE MIO

Reviews:

Related manuals for CAFFE MIO

Brands by name

Popular brands