VKI Technologies CAFFE MIO Operation & Service Manual Download Page 35

Page: 35 / 110

S E C T I O N 4 - T R O U B L E S H O O T I N G

CAFFÈ MIO – OPERATION AND SERVICE

Page 35 of 110

T r o u b l e s h o o t i n g

Coffee

Bitter / Too Strong

►

Coffee setting may be too high – decrease the coffee setting.

►

“

TOP PAUSE

” setting may be too high – decrease the “

TOP PAUSE

” setting.

►

Brewer may require a thorough cleaning – clean the brewer.

►

Coffee may be stale or not within specifications – replace coffee.

►

Coffee blend may be too strong – replace the blend.

►

Water filter may need to be replaced.

►

Water tank may need to be delimed.

Too Weak

►

Ingredient dispenser may be empty – refill the dispenser with coffee.

►

Coffee setting may be too low – increase the coffee setting.

►

Water temperature setting may be too low – increase the temperature.

►

Coffee may be stale or not within specifications – replace coffee.

►

Coffee blend may be too mild – replace the blend.

►

Increase “

TOP PAUSE

” to increase the strength of the coffee.

►

Ingredient dispenser may not be coupled properly with the motor – remove

dispenser and re-install it, making certain it is coupled with the motor.

Short Cup Dispensed

►

Water setting may be too low – increase the water setting.

►

Water tank may not be filling quickly enough – verify main water pressure, hoses

and inlet valve.

►

Water filter may be clogged – replace water filter.

►

If a self-piercing saddle valve was used to tap into the water supply, the valve may

have an obstruction – close and open the valve.

►

Brewer may be leaking or flooding – verify the brewer operation and repair, if

necessary.

►

Outlet valve may be defective – repair or replace outlet valve

(P/N - M029082)

No Product Dispensed

►

Ingredient dispenser may be empty – refill the dispenser with coffee.

►

Coffee setting may be set too low – increase the coffee setting.

►

Wiring may not be connected to the dispenser motor – verify the wiring.

►

Dispenser motor may be defective – replace dispenser motor

(P/N - C110043)

►

Ingredient dispenser may no be coupled properly with the motor – remove

dispenser and re-install it, making certain it is coupled with the motor.

►

Rear board may be defective – replace the rear board

(P/N - G410232MIO)

Summary of Contents for CAFFE MIO















































































































Search results

Summary of Contents for CAFFE MIO

Reviews:

Related manuals for CAFFE MIO

Brands by name

Popular brands

VKI Technologies CAFFE MIO, Operation & Service Manual

Search results

Summary of Contents for CAFFE MIO

Reviews:

Related manuals for CAFFE MIO

Brands by name

Popular brands