16
EN
Use your machine, accessories,
etc.., according to its type and
with these instructions, taking into
account the working conditions
of service to be performed.
The use of electrical equipment
for operations different from those
to which it is intended can result
in complicated situations.
Keep cutting tools sharp and clean.
Properly cared for cutting tools with
sharp edges are less likely to break
and saomais easy to control.
SERVICE
Keep your machine magazine and
repaired by qualified personnel,
using only replacement parts equal
to the originals. This will ensure the
maintenance of safety standards of
your machine.
ADDITIONAL RULES
FOR CIRCULAR SAWS
Danger: Keep hands away
from cutting area and the blade.
Keep one hand in supporting
or assisting in motor protection.
If both hands are holding
the machine can not be cut
by the blade.
Do not stand underneath
the workbench. The protection
does not protect the blade in these
conditions.
Setting the cutting depth according
to the thickness of the workpiece.
Less than a full tooth blade will be
visible below the workpiece.
Never hold piece being cut in your
hands or on top of the legs.
Hold the piece on a stable platform.
It is important to support the work
properly to minimize body exposure,
blade tilt and lose control.
Hold the machine with clamps grip
when performing work in which
the cutting tool may contact hidden
wires or even with the cable.
Contact with bare wire will expose
the metal parts of the machine
may cause electrical shock to the
operator.
When cutting, always use a rip
fence or straight edge guide.
This will improve the accuracy
of cutting and reduce the possibility
of jamming the blade.
Always use blades with correct size
and shape (diamond versus round)
of shaft holes. Blades that do not
match the mounting hardware of the
saw will run eccentrically, causing
loss of control.
Never use blade washers or bolts
improper or damaged. Washers
and bolts are designed specifically
for your machine, for optimum
performance and safety.
CAUSES AND
PRECAUTIONS
TO PREVENT OPERATOR
KICKBACK
Kickback is a sudden reaction
to a grip, breakage or misalignment
of the mountain, causing
an uncontrolled saw jump
off the workbench and towards
the operator.
When the blade is pressed
or pushed hard by lowering
the protection, reaction and the
blade stops the motor quickly
directs the machine to the operator.
If the blade is twisted or misaligned
with the cutting teeth in the back
of the blade can enter the timber
causing the exit channel and exit
towards the operator.
Kickback is the result of misuse
and / or incorrect operating
procedures or conditions and can
be evitadotomando the following
precautions:
Hold the machine with both hands
and position your arms so that they
resist the forces caused
by kickback. Position your body
to one side of the blade, not in line
with this. The kickback can cause
the saw to jump backwards, but its
strength can be controlled
by the machine operator if proper
precautions are taken.
When the blade gets stuck or when
the cut is interrupted for any reason,
release the trigger and hold the saw
motion in the material until
the blade stops completely.
Never attempt to remove the saw
from the work or pull it while the
blade is in motion as this may cause
a kickback. Investigate and make
examinations correction to eliminate
the cause of blade binding.
At the start of the work saw, center
the saw blade in the pipeline and
make sure blade teeth are not
engaged into the material.
If the blade is stuck, it can go up
and come back at the same time it
is restarted.
Use of Support large panels
to minimize the risk of compression
and kickback of the blade.
Large panels tend to sag under
their own weight. Supports must
be placed under the panel on both
sides, close to the cut line and the
edge of the panel.
Do not use blades dulled
or damaged. Blades sharpened
improperly adjusted or not produce
a rip narrow causing excessive
friction, warping or kickback blade.
The depth and squareness of the
blade should be locked and tight
before making a cut. If adjusting the
blade to move while cutting, it may
cause binding and kickback.
Take extra caution when making
cuts in existing walls or blind areas.
The cutting blade can cut objects
that cause kickback.
Summary of Contents for PRO-POWER 9711675
Page 27: ......
