Vitek VT-8518, Manual Instruction, Page: 4 / 24

4
ENGLISH
• Do not attempt to repair the unit. Do not
disassemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and contact any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
•
To avoid damages, transport the unit in the
original packaging only.
• Keep the unit out of reach of children and
people with disabilities.
THE UNIT IS INTENDED FOR HOUSEHOLD
USE ONLY, ITS COMMERCIAL USAGE AND
USAGE IN PRODUCTION AREAS AND WORK
SPACES IS PROHIBITED.
BEFORE USING THE UNIT
After unit transportation or storage at low
temperature keep it for at least three hours
at room temperature before switching on
.
•
Unpack the unit completely and remove any
advertising stickers that can prevent the unit
operation.
• Check the unit for damages, do not use it in
case of damages.
•
Before switching the unit on, make sure that
your home mains voltage corresponds to
the unit operating voltage.
•
Before the first use wash all the removable
parts (1, 2, 4) with warm water and neutral
detergent and then dry thoroughly.
• Clean the motor unit (6) with a soft, slightly
damp cloth and then wipe it dry.
•
Do not immerse the motor unit (6) into
any liquids and do not wash it with water.
• Place the blender only on a flat steady sur-
face.
ATTENTION! Continuous operation time of
the blender should not exceed 2 minutes; then
switch the unit off and let it cool down for 1
minute. After four operation cycles make a
break of at least 10 minutes.
• Do not remove the blender bowl and the
bowl lid during the operation.
USING THE BLENDER
•
Insert the measuring cup (1) into the lid (2)
opening, matching the corresponding
ledges on the measuring cup (1) and the
grooves on the lid (2), and turn the measur-
ing cup clockwise until bumping.
• Install the blender bowl (4) on the motor
unit (6) (the symbol
▼
on the blender
bowl (4) should match the symbol
▲
on the
motor unit (6)).
• Put the necessary ingredients into the
bowl (4).
Notes
–
Before starting to chop/mix, we recom-
mend to peel fruit, remove inedible parts,
such as stones, and cut fruit into cubes
approximately 2х2 cm in size.
–
The blender is not intended for beating
eggs, making potato mash, kneading
dough, extracting fruit or vegetable juice,
chopping hard or frozen products, chop-
ping meat and meat products.
–
The amount of foodstuffs to be processed
should not exceed 2/3 of the capacity of
the bowl in which they are processed or
be below the minimal “0.4 l” mark of the
blender bowl.
–
For easy control of the amount of the pro-
cessed food there is a liquid scale in liters
on the blender bowl (4).
• Install the lid (2) on the blender bowl (4) until
the lock (3) clicking.
•
Make sure once again that the blender
bowl (4) is installed correctly.
• Insert the power plug into the mains socket.
Note: The blender will not switch on if the
blender bowl (4) is not installed properly and
not covered with the lid (2).
• Use the operation mode switch (7) to set the
required rotation speed of the knives:
– «
0 » the blender is off
– « Min » (low speed) – for mixing liquid
products.
– «
Max » (high speed) – for liquid and hard
products.
•
To switch the pulse mode on, set the
switch (7) to the position “
P
” and hold it for
several seconds.
•
During the operation or between the opera-
tion cycles, you can add the required ingre-
dients into the bowl (4). To do this, turn the
measuring cup (1) counterclockwise and
remove it. After adding ingredients through
the lid (2) opening, install the measuring
cup (1) back to its place.
• After the unit operation is finished, set the
operation mode switch (7) to the «
0 » posi-
tion and unplug the unit.
IM VT-8518.indd 4 03.07.2018 15:57:56