Vitek VT-1193, Manual Instruction

Page: 6 / 32

6
ENGLISH
•
The preset keep warm temperature is shown
by the digital symbols (18).
• When you select the room temperature
mode, the indicator (20) «ROOM TEMP» will
light up, the symbols (18) «--» will appear on
the display (17). In this mode water in the
thermopot will cool down to the temperature
25°С, after that the boiling mode will switch
on. After boiling water will be cooling down
to 25°С again.
Notes: - to reboil the water press the button (26)
«REBOIL». The indicator (25) «BOILING» will light
up. To switch the reboiling mode off press the
button (26) «BOILING» again, the indicator (25)
«BOILING» will go out and the thermopot will
switch back to the keep warm mode.
•
Drain the water; to do this, you must unlock
the activation of the water pump by pressing
button (24) « UNLOCK», the light indicator
(24) « UNLOCK» will light up.
Attention! Be careful when pouring out water to
avoid burns by hot water.
Version 1:
–
place a suitable bowl, for instance, a cup
under the spout for pouring water (4) and
press the water dispense button (3) with a rim
of the cup.
Version 2:
–
place a suitable bowl under the spout for
pouring water (4) and press the water dis-
pense button (23) «DISPENSE».
Notes: - the water is dispensed only when the
indicator (24) « UNLOCK» is switched on; if
you pressed the button (24) « UNLOCK» and
didn’t do anything, the indicator (24) will go out
in 10 seconds.
•
To switch the thermopot off disconnect the
power plug (16) from the mains socket.
Notes: - after 48 hours the thermopot will
switch to the standby mode, the indicator (25)
«BOILING» will be flashing a little bit. To switch
off the standby mode press any button on the
control panel (5).
•
Open the thermopot lid (8) and wait until it
cools down completely, remove the lid (8)
(see the chapter BEFORE THE FIRST USE),
drain the water, install the lid (8) back to
its place and put the thermopot away for
storage.
Overheating protection
• If you accidentally switched the thermopot
on and the water level is below the minimal
mark, the automatic thermal switch will be on,
you will be hearing sound signals for 20 sec-
onds, all indicators (20, 22, 23, 24, 25) on
the control panel (5) will be flashing and the
symbols «E2, E1» (19) will appear. In this case
unplug the thermopot and let it cool down
for 20-30 minutes, then fill it with water, and
switch the thermopot on, the unit will operate
in normal mode.
CLEANING AND CARE
•
Before cleaning, disconnect the thermopot
from the mains, pour out water and let the
thermopot cool down completely.
•
Before removing the lid (8) open it and pull the
lid (8) to the control panel (5).
•
Carefully tilt the thermopot to drain the
remaining water.
•
Install the lid (8) in the lock (9). To do it, place
the lid (8) at a small angle and insert the lid
(8) into the lock (9). Before using the thermo-
pot make sure that the lid (8) is fixed properly.
•
Clean the outer surface of the thermopot with
a slightly damp cloth and then wipe it dry.
•
Use neutral detergents to remove dirt; do not
use metal brushes, abrasive detergents and
solvents.
•
Do not immerse the thermopot and the power
cord into water and other liquids.
•
Do not wash the thermopot in a dishwashing
machine.
Stains on the inner surface
of the thermopot
The inner surface of the metal flask may change
its color under the influence of different water
impurities.
•
You can remove the stains with citric acid or
vinegar.
• To remove the flavour of citric acid or vinegar,
boil water and pour it out.
•
Repeat this procedure until the smell and
taste vanish completely.
Descaling
•
Scale, appearing inside the metal flask,
causes the heating element overheating and
malfunction. Burning of the heating element
IM VT-1193.indd 6 11/26/19 2:32 PM