manualshive.com logo in svg

Virgo VRG14PL, User Manual, Page: 27 / 40

Share
Download
Virgo VRG14PL User Manual Download Page 27

LAMINATING & 

UNWINDING MODULE

WASTE REMOVING & 

REWINDING MODULE

MEDIA PATH

ULTRASONIC SENSOR CALIBRATION

LAMINATING & UNWINDING 

MODULE

1. Turn OFF the main power “ON-OFF”  
red switch.

2. Raise up the tension arm up to the 
desired position (generally it is in the 

middle of the range). In that position, 

the system will reach the maximum 
unwinding’s speed. The longer your 
label will be, the lower tension arm 
position requires to be set.

3. Holding the tension arm idle at 
the desired position, keep pushed 
“

Forward Media

” button, in the mean 

time turn ON the main power red 
switch and wait until the yellow led will 

have flashed 3 times and an acoustic 

beep signal will have been issued.

4. The ultrasonic sensor has been 
calibrated and ready to be operative.

WASTE 

MATRIX

FINISHED 

ROLL

LAMINATION 

ROLL

PRINTED

 ROLL

WASTE REMOVING & REWINDING 

MODULE

1.  Keeping ON the main power “ON-
OFF” red switch. Turn “OFF” the 

module (both leds are off).

1. Raise up the tension arm up to the 
desired position (generally it is in the 

middle  of  the  range).  That  point  will 

determinate the tension arm working 
range from the bottom position. The 
longer your label will be, the lower 
tension arm position requires to be set.

2. Holding the tension arm idle at the 
desired position, using a paper clip, 
keep pushed the button into the small 
hole until the yellow led will have 

flashed 3 times.

3. The ultrasonic sensor has been 
calibrated and ready to be operative.

26

Summary of Contents for VRG14PL









































Reviews:

No comments