VIPA SPEED7 CPU 313SCDPM Manual Download Page 68

Page: 68 / 205

5.12.2

Function security

The CPUs include security mechanisms like a Watchdog (100ms)

and a parametrizable cycle time surveillance (parametrizable min.

1ms) that stop res. execute a RESET at the CPU in case of an error

and set it into a defined STOP state. The VIPA CPUs are developed

function secure and have the following system properties:

Event

concerns

Effect

RUN

STOP

general

BASP (Befehls-Ausgabe-Sperre, i.e. com-

mand output lock) is set.

central digital outputs

The outputs are disabled.

central analog outputs

The outputs are disabled.

Voltage outputs issue 0V

Current outputs 0...20mA issue 0mA

Current outputs 4...20mA issue 4mA

If configured also substitute values may be

issued.

decentral outputs

Same behavior as the central digital/analog

outputs.

decentral inputs

The inputs are cyclically be read by the

decentralized station and the recent values

are put at disposal.

STOP

RUN res.

PowerON

general

First the PII is deleted, then OB 100 is

called. After the execution of the OB, the

BASP is reset and the cycle starts with:

Delete PIO

Read PII

OB 1.

decentral inputs

The inputs are once be read by the decen-

tralized station and the recent values are

put at disposal.

RUN

general

The program execution happens cyclically

and can therefore be foreseen: Read PII

OB 1

Write PIO.

PII: Process image inputs, PIO: Process image outputs

5.13 Overall reset

During the overall reset the entire user memory is erased. Data

located in the memory card is not affected. You have 2 options to ini-

tiate an overall reset:

initiate the overall reset by means of the operating mode switch

initiate the overall reset by means of the Siemens SIMATIC Man-

ager

You should always issue an overall reset to your CPU

before loading an application program into your CPU to

ensure that all blocks have been cleared from the CPU.

Overview

VIPA System 300S

Deployment CPU 313-6CF13

Overall reset

HB140 | CPU-SC | 313-6CF13 | GB | 15-50

Summary of Contents for SPEED7 CPU 313SCDPM














































































































































































































Search results

Summary of Contents for SPEED7 CPU 313SCDPM

Reviews:

VIPA SPEED7 CPU 313SCDPM, Manual, Page: 68 / 205

Search results

Summary of Contents for SPEED7 CPU 313SCDPM

Reviews: