Post Effects
42
Rev. 2.0 - EN EU - fw 5.22
9
PAGE 1/3 - DELAY ROUTING AND RANGE
The menu on this page allows you to position (or route) your delay on either
the left or right channel. If you use the PedalPro in a mono configuration,
select ‘left’ to insert the Delay in your effect chain (see
Fig. 9-2
and
Fig. 9-3
,
on page 37).
Routi ng
1/3
D l
e a
È
Range: 23 0 9ms
- 9
y
: e t
l f
Routing
– Routing selector. Range: none, left, right
•
To change the routing, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position
the blinking cursor next to Routing. Adjust the value with the
selection
dial
[
4
]. When ‘
none
’ is selected, the
Delay effect is deactivated
.
Range
– Available delay range. Range: 23-99 ms (short), 40-409 ms (medium),
61-614 ms (long)
•
To set the available delay range, press
EDIT
[
5
]. Use the
arrow keys
[
3
]
to position the blinking cursor next to Range. Adjust the value with the
selection dial
[
4
].
PAGE 2/3 - DELAY CONFIGURATION
This is the configuration page for the parameters of the Delay.
Ti me: 40 .
0 7
2/3
D l
e ay
È
I np: 050.
ut:
5
7
0
.
5
Wet: 045.
bk :
0
1
0
.
0
1
2
ms
O
F
Time
– Amount of delay applied. Range: 23-99 ms (short), 40-409 ms (me-
dium), 61-614 ms (long)
•
To change the amount of delay, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to
position the blinking cursor next to Time. Adjust the value with the
selec-
tion dial
[
4
].
Inp
– Input signal level selector. Range: 0-100%
The Inp (input) parameter controls the level of the signal at the input of the
Delay effect.
•
To adjust the input signal level, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to
position the blinking cursor next to Inp. Adjust the value with the
selection
dial
[
4
].
Wet
– Wet/dry ratio control. Range: 0-100%
The Wet parameter allows you to control the ratio between delayed signal
(wet) and input signal (dry) in the Delay output signal.
•
To alter the wet/dry ratio of the Delay, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position the blinking cursor next to Wet. Adjust the value with the
selection dial
[
4
]..
Out
– Delay output level. Range: 0-100%
The Out parameter controls the output level of the analogue Delay effect..
•
To adjust the output level of the Delay, press
EDIT
[
5
]. Use the
arrow keys
[
3
] to position the blinking cursor next to Out. Adjust the value with the
selection dial
[
4
].
TIPS & TRICKS - DELAY
•
For short delays (doubling echo, slapback, reverberation emulator) set
the
Range
parameter to ‘short’; this gives you access to an analogue
delay with an adjustable range of 23-99 ms.
•
For medium delays (slapback and infinite loops) set the
Range
to ‘me-
dium’; you can select your analogue delay from a range of 40-409ms.
•
For long delays (infinite loops, small phrase loops) set
Range
to ‘long’;
this produces an analogue delay with a range between 61-614 ms.
•
Finally, adjust the amount of delay applied, within the range that you
have just selected, on page
2/3
of the Delay configuration menu (pa-
rameter
Tempo
).
