Vingtor Stentofon 3005050028 Technical User'S Manual Download Page 69 | Manualshive

Page: 69 / 79

background image

Document: 1795en03.doc

WESTERSTRAND

Author: PM

Date: May 8, 2014

Page: 10 of 11

WESTERSTRAND URFABRIK AB

P.O. Box 133

Tel. +46 506 48000

Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA

Fax. +46 506 48051

E-mail:

[email protected]

NTP >>

Used to set the NTP parameters.

NTP mode

NTP mode is set from the Master Clock keyboard, special function SETUP/SYNC SOURCE. See page 5.
Server: The Ethernet module answers time request from clients.
Client/Server: The Ethernet module acts as both a NTP client and a NTP server.

Broadcast/Multicast Interval(s)

---

No periodic transmission of time. A client will ask for time.

Broadcast

Transmit time periodic to IP=255.255.255.255

Multicast

Transmit time periodic to IP=224.0.1.1

Client NTP clock

With periodic transmission client network clocks will show a new time quicker. Make sure the

client clock has enabled broadcast/multicast, e.g. NTP mode = Broadcast/Multicast. Also

Country/Timezone = Local Time must be selected in the client clock.

Timebase

With this function the type of time transmitted in the NTP message is chosen. Default=UTC.

NTP server 1..5

This function is used if the Time Central is receiving time from an external NTP Server and NTP
mode Client/Server. The value entered can be either an IP-address or a name if the DNS
server (name server) functionality is used. Server ip address is then the address of the external NTP Server.

Interval(s)

NTP client poll interval in seconds
This function is used if work NTP Client/Server is selected.

Max. correction (s)

This function is used if the Ethernet module is configured as an NTP client
Enter max. correction in seconds. The time is compared with current time in the Time Central. If 0 is chosen,
then no check of the time is done.

«
...
67
68
69
70
71
...
»

Summary of Contents for 3005050028
















































































Reviews:

No comments

Related manuals for 3005050028

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: Tate Pages: 7

Brand: Tate Pages: 5

BioHarmonex BH4

Brand: Calivita Pages: 38

Brand: CAIRE Pages: 91

Brand: NCR Pages: 20

Brand: DARAY Pages: 32

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: MacDon Pages: 74

Brand: Eaton Pages: 2

Brand: Eaton Pages: 20

Brand: Coba Pages: 2

Brand: Exalto Pages: 28

Brand: PURE Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands