Vingtor Stentofon 3005050028 Technical User'S Manual Download Page 10

Page: 10 / 79

MARINE MASTER CLOCK

Document: 1717en19.doc

Author: PM

User Manual

Date: 2017-12-22

Page: 7 of 51

WESTERSTRAND URFABRIK AB

P.O. Box 133

Tel. +46 506 48000

Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA

Fax. +46 506 48051

E-mail:

[email protected]

Installation

The Marine Master Clock is intended for stand, cabinet, wall or desk mounting.

1.

Mount the Master Clock.

Make sure that all analogue slave clocks shows the same time, for instance 12.00.

Before connecting the slave clock lines, check the wires for short circuit, faulty connections etc.

Connect the slave clock lines.

Connect the signal line/lines (to relay contacts).

NOTE! For connection of signals etc., mixed voltages must not be used.
Therefore, choose either 230VAC or, for example 24VAC for connection to the relays.

Connect, if included, other accessories/options such as radio synchronisation, RS232 etc.

Connect the supply voltage and press the power switch.

10.

Proceed to “Start up procedure” page 9.

Summary of Contents for 3005050028
















































































Search results

Summary of Contents for 3005050028

Reviews:

Related manuals for 3005050028

Brands by name

Popular brands

Vingtor Stentofon 3005050028, Technical User'S Manual

Search results

Summary of Contents for 3005050028

Reviews:

Related manuals for 3005050028

Brands by name

Popular brands