Vingtor Stentofon 3005050028 Technical User'S Manual Download Page 37

Page: 37 / 79

MARINE MASTER CLOCK

Document: 1717en19.doc

Author: PM

User Manual

Date: 2017-12-22

Page: 34 of 51

WESTERSTRAND URFABRIK AB

P.O. Box 133

Tel. +46 506 48000

Internet:: http://www.westerstrand.se

SE-545 23 TÖREBODA

Fax. +46 506 48051

E-mail:

[email protected]

Setup sync. source

Below is a description of the different configuration parameters available in the setup menu for

sync. source

Please remark that if default settings are used no configuration is needed.

Type of synchronisation

State type of external synchronisation. The following time sources can be selected:

NMEA RS485 (default)

Synchronisation using RS485 input and NMEA ZDA protocol.

NMEA RS232

Synchronisation using RS232 input and NMEA ZDA protocol.

W-GPS

Radio synchronisation GPS type Westerstrand.

DCF77

Radio synchronisation DCF77.

Time code type hard wired DC

--------

No external synchronisation

Alarm limit

The configuration parameter

Alarm limit

specifies the time delay before the radio alarm is activated. Default

setting is that the radio alarm is inactivated, AL.LIMIT --h--m.

NMEA RS485
AL. LIMIT --h--m

Type of synchronisation

Alarm limit

Summary of Contents for 3005050028
















































































Search results

Summary of Contents for 3005050028

Reviews:

Related manuals for 3005050028

Brands by name

Popular brands

Vingtor Stentofon 3005050028, Technical User'S Manual

Search results

Summary of Contents for 3005050028

Reviews:

Related manuals for 3005050028

Brands by name

Popular brands