VIKING GARDEN iMow MI 632 M, Instruction Manual

Page: 169 / 446

167
DE
FR
NL
IT
EN
0478 131 9937 B - EN
– Perimeter wire incorrectly routed in
area of docking station
– Ends of perimeter wire not cut
Remedy:
– Level out the entry area to the docking
station ( Ö 9.2)
– Clean the drive wheels and the floor
plate of the docking station ( Ö 16.2)
– Re-route the perimeter wire – ensure
correct routing in the area of the
docking station (
Ö
12.3)
– Cut the perimeter wire as described and
route it without excess length – do not
roll up protruding ends (
Ö 9.12)
Fault:
The robotic mower travels past the
docking station or docks at an angle
Possible cause:
– Wire signal affected by
– Perimeter wire incorrectly routed in
area of docking station
Remedy:
– Link the robotic mower and docking
station again – ensure that the robotic
mower is in correct alignment to the
docking station (
Ö 9.14)
– Re-route the perimeter wire – ensure
correct routing in the area of the
docking station (
Ö 12.3)
Check for correct connection of the
perimeter wire ends in the docking
station (
Ö 9.12)
Fault:
The robotic mower has crossed the
perimeter wire
Possible cause:
– Perimeter wire incorrectly routed,
clearances are not correct
– Slope inclination of mowing area too
steep
– Interference affecting the robotic mower
Remedy:
– Check the routing of the perimeter wire
(Test edge) ( Ö 11.6) check the
clearances
– Check the routing of the perimeter wire;
block off areas with excessively steep
slope inclinations (Test edge) (
Ö 11.6)
– Contact a VIKING specialist dealer (
#
)
Fault:
The robotic mower frequently becomes
stuck
Possible cause:
– Cutting height too low
– Drive wheels dirty
– Depressions or obstacles in the mowing
area
Remedy:
– Increase the cutting height ( Ö 9.8)
– Clean the drive wheels (
Ö
16.2)
– Fill up holes in the mowing area, install
no-go areas around obstacles such as
exposed roots, remove obstacles
(
Ö 12.3)
Fault:
Impact sensor is not activated when the
robotic mower hits an obstacle
Possible cause:
– Low obstacle (height less than 10 cm)
– The obstacle is not firmly attached to
the ground – e.g. fallen fruit or tennis
ball
Remedy:
– Remove the obstacle or block it off with
a no-go area ( Ö 12.6)
– Remove the obstacle
Fault:
Driving tracks at edge of mowing area
Possible cause:
– Excessively frequent edge mowing
– Starting points in use
– Battery is charged very frequently
towards the end of its service life
– Offset drive home (passage) not
switched on
Remedy:
– Switch off edge mowing or reduce it to
once per week ( Ö 10.)
– Start all mowing operations at the
docking station in suitable mowing
areas (
Ö 10.)
– Replace the battery – observe
corresponding recommendation on the
display (
#
), ( Ö 24.)
– Switch on offset drive home (passage)
(TeaM installation) (
Ö
11.6)
Fault:
Unmown grass at edge of mowing area
Possible cause:
– Edge mowing switched off
– Perimeter wire routed inaccurately
– Grass is out of reach of mowing blade
Remedy:
– Mow the edge once or twice per week
(
Ö
10.)
– Check the routing of the perimeter wire
( Ö 12.3), check the clearances
– Cut the unmown areas regularly using a
suitable grass trimmer
Fault:
No wire signal
Possible cause:
– Master docking station switched off –
no LED illuminates