VIKING GARDEN iMow MI 632 M, Instruction Manual

Page: 168 / 446

0478 131 9937 B - EN
166
Fault:
The robotic mower is not working and
nothing is shown in the display
Possible cause:
– Machine is in standby
– Battery defective
Remedy:
– Press any button to wake up the robotic
mower – the status screen appears
(
Ö
11.2)
– Replace the battery (
#
)
Fault:
The robotic mower is noisy and vibrates
Possible cause:
– Mowing blade is damaged
– Mowing deck is very dirty
Remedy:
– Replace the mowing blade – remove
any obstacles from the lawn (
Ö
16.4),
(
#
)
– Clean the mowing deck ( Ö 16.2)
Fault:
Poor mulching or mowing result
Possible cause:
– Grass is too high in relation to the
cutting height
– Lawn is extremely wet
– Mowing blade is blunt or worn
– Active times insufficient, mowing
duration too short
– Size of mowing area set incorrectly
– Mowing area with very high grass
– Long periods of rain
Remedy:
– Adjust the cutting height ( Ö 9.8)
– Set the rain sensor ( Ö 11.6)
Change the active times ( Ö 10.)
– Replace the mowing blade ( Ö 16.4),
(
#
)
– Extend or add active times ( Ö 10.)
Extend the mowing duration ( Ö 10.)
– Create a new mowing plan ( Ö 10.)
– For neat mowing results, the robotic
mower needs up to 2 weeks, depending
on the size of the mowing area.
– Allow mowing in the rain (adjust the rain
sensor) ( Ö 11.6)
Extend the active times ( Ö 10.)
Fault:
Display in a foreign language
Possible cause:
– Language setting has been changed
Remedy:
– Set the language (TeaM settings)
( Ö 11.6)
Fault:
Brown (earthy) patches appear in the
mowing area
Possible cause:
– Mowing duration is too long in relation
to the mowing area
– Perimeter wire has been routed with
excessively tight radii
– Size of mowing area set incorrectly
Remedy:
– Reduce the mowing duration ( Ö 10.)
– Correct the routing of the perimeter wire
( Ö 9.11)
– Create a new mowing plan ( Ö 10.)
Fault:
Mowing operations are significantly
shorter than usual
Possible cause:
– Grass is very high or too wet
– Machine (mowing deck, drive wheels) is
very dirty
– Battery has reached end of service life
Remedy:
– Adjust the cutting height ( Ö 9.8)
Set the rain sensor (TeaM settings)
(
Ö 11.6)
Change the active times ( Ö 10.)
– Clean the machine ( Ö 16.2)
– Replace the battery – observe
corresponding recommendation on the
display (
#
), ( Ö 24.)
Fault:
The robotic mower is docked, the battery is
not charging
Possible cause:
– The battery does not need to be
charged
– Docking station not connected to power
supply
– Incorrect docking
– Charging contacts corroded
Remedy:
– No action necessary – battery charging
occurs automatically below a certain
voltage
– Check the power supply to the docking
station ( Ö 9.5)
– Place the robotic mower in the mowing
area and send it back to the docking
station (
Ö 10.), check for correct
docking – if necessary, correct the
position of the docking station (
Ö 9.2)
– Replace the charging contacts (
#
)
Fault:
Docking not working
Possible cause:
– Uneven entry area to docking station
– Dirty drive wheels or dirty floor plate