Viessmann Vitocaldens 222-F Installation Instructions Manual Download Page 53

Page: 53 / 60

Please note

Ensure the specified mini-
mum lengths above the roof
are observed.
Never trim roof outlets
above the roof.

Roof outlet

■ Use universal tiles or air vent tiles

with pipe outlets.

■ Position balanced flue slide cou-

pling

underneath the roof out-

let.

■ Install pipe outlets for Klöber or

universal roof tiles in accordance
with manufacturer's instructions.

■ Position the roof outlet onto the

roof tiles from above.

■ Connect the external wall pipe

from below.

Elbow in the external routing for
a short roof overhang

■ Elbow with 45° bend

: Fit bal-

anced flue inspection piece

■ Elbow with 30° bend

: Bal-

anced flue inspection piece

not required.

■ Fit external wall terminal

Routing over an external wall

(cont.)

5780 223 GB

Summary of Contents for Vitocaldens 222-F





























































Search results

Summary of Contents for Vitocaldens 222-F

Reviews:

Related manuals for Vitocaldens 222-F

Brands by name

Popular brands

Viessmann Vitocaldens 222-F, Installation Instructions Manual

Search results

Summary of Contents for Vitocaldens 222-F

Reviews:

Related manuals for Vitocaldens 222-F

Brands by name

Popular brands