Viessmann TectoCell Standard Plus 100 Installation And Operating Instructions Manual Download Page 15

Page: 15 / 20

Decommissioning

5777744-03 GB Subject to technical changes!

Elements with a powder-coated sheet steel or

stainless steel surface:

Do not spray-clean the inside or outside of the walls,

ceilings, elements with electrical components (such

as door frame) and unit with water.

Wipe out the inside of the room, dry it completely

and air it out well.

Do not use any scouring agents or cleaning agents

that contain solvents.

Wipe the outside of the room with a damp cloth and

dry it off.

Standard floor:

Wipe with damp cloth only.

Do not clean standard floors with water jet.

Make sure there is no water on standard floors.

Tub floor:

Wipe with damp cloth only.

Only expose tub floor to standing water or water jet

for a short amount of time.

For all floors:

Regularly wash off door seals with neutral soap

solution and dry them off.

Do not use acetone or cleaning agents that contain

solvents to clean the seals.

Treat stainless steel room floor with standard com

mercial stainless steel cleaning agents.

Seal stainless steel surface with stainless steel care

product.

Observe product information on cleaning agents.

8 Decommissioning

For prolonged downtime:

Pull the power plug or shut off the mains power.

Ensure adequate ventilation.

9 Technical data

9.1

Permissible loading on floor elements

Load
Weight
Class

Wheel

Wheel Load (N**)

Wheel

Load (N/

)

1 - 4 cm

> 4 cm

Rubber

400

1.600

30.000

PU-/Rubber

750

3.000

40.000

PU-/Rubber

1.000

4.000

50.000

4.*

PU-/Rubber

1.250

5.000

50.000

* Load Weight Class 4) Special version for 5.000N floor: Extension of approval

up to 6.000N possible after interal check.möglich nach interner Prüfung

** 10N ≈ 1Kg

10 Maintenance

DANGER!

Risk of death due to electric

shock!

Ensure that maintenance work

is carried out exclusively by trained

qualified personnel.

Disconnect power plug and se-

cure to prevent reconnection before

carrying out maintenance work.

Conduct maintenance on TectoCell cold rooms and

deep-freezing rooms at least once per year.

You can reach our technical customer service at:

+49 9281 814 908

11 Disposal

Dispose of defective TectoCell cold rooms and

deep-freezing rooms in an environmentally friendly

manner according to applicable disposal regula-

tions.

12 Standards and laws

Comply with the applicable standards and laws:

EMC directive 2014/30/EG

Machinery Directive 2006/42/EC, DIN EN 378

(2008/2012)

Summary of Contents for TectoCell Standard Plus 100





















Search results

Summary of Contents for TectoCell Standard Plus 100

Reviews:

Related manuals for TectoCell Standard Plus 100

Brands by name

Popular brands

Viessmann TectoCell Standard Plus 100, Installation And Operating Instructions Manual

Search results

Summary of Contents for TectoCell Standard Plus 100

Reviews:

Related manuals for TectoCell Standard Plus 100

Brands by name

Popular brands