Videx IP videokit IPVK/6296 Series, Installation Handbook

Page: 44 / 76

66550062-EN - V6.0 - 31/10/21
- 44 -
IPVK/6296 Series IP videokit
IPVK/6296 Series - Installation handbook
SETTING UP A VIDEO INTERCOM 6296
In the device list ( Fig. 38 ), click on the button “Edit Properties” of one “VIDEO INTERCOM”. If you are unsure which videophone is
which, you can enable the flag “Accept Connections from Devices” under the software preferences then press any button on the
videophone to open the settings for that videophone.
The “ INTERCOM SETTINGS ” window ( Fig. 39 ) shows the following device information:
• The Device Model
• The firmware version
• The hardware version
Then there is a section of editable fields*:
• The Device IP
• The Subnet Mask
• The Gateway IP
• The DNS 1
• The DNS 2
• The Device ID
• The Device Description
*If you are not sure, contact your system administrator to set the correct IP Address, subnet mask and Gateway.
If you are not sure,, contact your system administrator to set the correct IP Address, subnet mask and Gateway. It is recommended
to set a descriptive “ DEVICE DESCRIPTION ” that identifies the area where the device is installed i.e. “Ground Floor”, “Kitchen” etc.
For some intercom buttons, it is possible to configure their function depending on the videophone status: stand-by, in conversation
and/or ringing.
In the “ GENERAL ” tab ( Fig. 39 ) you have the following:
• “AUDIO SETTINGS” Section
» Check the “Noise Attenuation” flag to improve audio quality in case of noisy environments.
» Check the “Camera Recall With Mic Mute” flag if you want the camera recall to start with the handset microphone in mute
mode otherwise it will start with the speech open.
» The “Number Of Rings” listbox allows the operator to set the number of rings for the selected videophone, this setting can be
carried out from the videophone’s menu also.
» The “Ringtone” listbox allows the operator to set the melody for the selected videophone, this setting can be carried out from
the videophone‘s menu also.
• “RINGTONE REPEATER” Section. Under this section it is possible to enable a relay when the videophone starts to ring.
» Select relay 1 or 2 of the videophone: the output will be activated as per relevant programming. If the programming is “Puls-
es/Ringtone repeater” the activation will stop as soon as the handset is picked up.
» Select an ethernet relay then select one of relevant relay: the output will be activated as per relevant programming. If the
programming of the ethernet relay is “Pulses/Ringtone repeater” the activation will stop as soon as the handset is picked up.
» Select “disabled” to disable the feature.
In the example of the picture, the one output of the “Service Relay” it is configured to operate as “ringtone repeater”. On an incoming
call, the relay will operate as per programming but will stop as soon as someone pick up the handset of the “Apt.1A” videophone.
The “ BUTTONS ” tab allows to configure the videophone’s buttons.
When a button is configured to activate a relay you can choose from the following options:
1. Relay 1 or 2 of the calling door panel (means the first or the second relay of the currently connected door panel).
2. A specific relay of a specific door panel (i.e. relay 1 of main entrance door panel) or a specific relay of an ethernet relay.
3. Disabled.
In the “
PRIVACY
” tab (
Fig. 40
) you have the following:
• For the “
IN STANDBY
” status, select the privacy duration from the drop down menu: in standby the button can only be used to
activate/deactivate the privacy service. The value “Infinite” means that the service switched ON/OFF only by pressing the button
while the other values mean that the service is timed so when the button is pressed starts a timer and the privacy will au-
tomatically switch off when the timer expires or the button is pressed again. When the privacy service is active, the videophone
does not receive any incoming call (external or internal).
• For the “ IN CONVERSATION ” status the button can be set as per the options described above 1,2 or 3.
In the “ SERVICE ” tab ( Fig. 41 ) you have the following:
• For the “ IN STANDBY ” status the button can be set as per the options described above 1 or 3. In the example the button is
configured to open the garden gate.
• For the “
IN CONVERSATION
” status the button can be set as per the options described above 1,2 or 3.
VX IP Wizard
Wizard configuration software for VIDEX IP System