vidaXL 50762, Operating And Safety Instructions Manual, Page: 18 / 376

18 | 50762
2) Fix the drainage pipe clip on the right of rear side plate near
drainage port with a screw.
3) Put the drainage pipe into drainage port and screw it up,
and then bind it with pipe hoop.
4) Put the rubber plug into other side of drainage pipe, fix it
with pipe hoop and then fix it in the drainage pipe clip.
• Drainage way as follows.
See image 8
1) In Cool or Dry mode operating, the condensation water will
be drained to the chassis.
2) When the chassis is full with water, the buzzer will give out
8 sounds and "H8" is displayed to remind user to discharge
water, the unit will turned off about 2min latter, and all
buttons are invalid.
To empty the chassis, please follow the instructions bellow.
– Turn the unit off and unplug from the electrical outlet.
– Use a small pan or move the unit to a suitable place to
drain the water.
– Take the drainage pipe from the clip and pull out the
rubber plug on the drainage pipe to drain the water.
– Drain the water into the small pan or a suitable place.
– Once draining is complete, re-install drain cap.
– Press ON/OFF button to restart the unit.
2. Use the continuous drainage option from the middle hole.
5
Note:Water can be automatically emptied into a floor
drain by attaching 14mm inner diameter hose (not included).
See image 9
1) Remove the continuous drain cap 1 by turning it counter
clockwise then remove the rubber stopper 2 from the
spout.
2) Screw the drain connector to (included in the package) the
spout by turning clockwise.
3) Insert the drainage hose into drain connector.
6
When using continuous drainage option from the middle
hole, place portable on a level surface and make sure garden
hose is clear of any obstructions and is directed downward.
Placing portable on an uneven surface or improper hose
installation may result in water filling up the chassis and
causing the unit to shut off. Empty water in the chassis if shut
off occurs, then check portable location and hose for proper
setup.
See image 10
5.5 Installation in a double-hung sash window
5
Note: If the inner width of window is below 20.5"
(520mm), please remove the adjusting panel from window
panel and then cut the window panel to make its width the
same as the width of window.
See image 11
1 Adjusting panel 3 Cut
2 Window panel
1. Install rear clip - aim the rear clip(upper) at the rear
clip(lower), fix them together, press the clasp forcibly in to
the groove.
See image 12
4 Rear connector (upper) 6 Clasp
5 Rear connector (lower)
2. Clamp joint B+C into the inner side of window panel along
the direction of arrow.
See image 13
7 Joint B+C 8 Inner side
3. Fix the protective grille on joint B+C with screws.
See image 14
9 Screws 10 Protective Grille
4. Fix the support on the outer side of window panel with
nuts, spring washer, washer and bolt.
See image 15
11 Spring washer 14 Bolt
12 Nut 15 Support
13 Washer
5. Fix the rain shield on the support with nuts, spring washer,
washer and bolt.
See image 16
16 Rain Shield
5
Note: protective grille, support, rain shield, nut, bolt,
spring washer and washer are optional accessories; some
models are without these accessories.
6. Cut the sponge B to a proper length and attach it to the
window sash.
See image 17
17 Sponge B (adhesive)
7. Attach the window panel to the window stool.
1) If the inner width of the window is less than 20.5" (520mm).
The window panel cannot be installed in windows less than
20.5" (520mm) wide.
See image 18
18 Window panel
assemble
20 Less than 20.5"
(520mm)
19 Window stool
a) Remove the adjustment panel from the window panel,
and cut the window panel to the same width as the
window.
b) Open the window sash and place the window panel on
the window stool.
c) Secure the window panel to the window stool with
screws.