background image

Manual Skylla with universal input  

1.3 

Warnings 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
The cover of the battery charger may only be removed by a qualified 
technician.

 

Before obtaining access to the battery charger the mains 

supply circuit must be disconnected. 

 
Explosive gasses can occur during charging a lead-acid battery. 
Prevent flames and sparks. 
Provide adequate ventilation during charging. 

 
The battery charger can not be used to charge non-rechargeable 
batteries. 

 

 

 
The on/off switch at the front of the cabinet does not switch off the 
mains supply. 
 

 

 
Disconnect  the  mains  supply  before  making  or  breaking  the 
connections to the battery. 
 

 

 
Do  not  use  the  voltage  sense  facility  in  combination  with  the 
diode-splitter  compensation.  This  will  raise  the  output  voltage, 
which could damage the battery. 

 
There is a dangerous voltage present on some of the metal parts 
inside the battery charger. 

 

 

 

The  battery  charger  is  NOT  protected  against  reverse  battery 
polarity. ("+" connected to "-" and "-" connected to "+").

   

Follow  the  installation  procedure.  The  warranty  expires  when  the 
battery charger becomes defective due to reverse battery polarity. 

Summary of Contents for 24/30































Reviews: