INDEX
Hazard Identification . . . . . . . . . . . . . . . . . . . . 1
Operator Safety Instructions . . . . . . . . . . . . . . . 2
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Tool Set-Up . . . . . . . . . . . . . . . . . . . . . . . . . 2
Operating Tool . . . . . . . . . . . . . . . . . . . . . . . 2
Tool Maintenance . . . . . . . . . . . . . . . . . . . . 3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Power Requirements . . . . . . . . . . . . . . . . . . 3
Extension Cord Requirements . . . . . . . . . . . 4
Tool Nomenclature . . . . . . . . . . . . . . . . . . . . . . 5
Receiving Tool . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tool Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Pre-Operation Adjustments . . . . . . . . . . . . . . 10
Grooving Rolls . . . . . . . . . . . . . . . . . . . . . . 10
Pipe Preparation . . . . . . . . . . . . . . . . . . . . 10
Groovable Pipe Lengths . . . . . . . . . . . . . . . 11
Roll Guard Adjustment . . . . . . . . . . . . . . . . 13
Pipe Stabilizer Adjustment . . . . . . . . . . . . . 14
Groove Diameter Stop Adjustment . . . . . . . 15
Grooving Operation . . . . . . . . . . . . . . . . . . . . 17
Roll Changing . . . . . . . . . . . . . . . . . . . . . . . .20
Roll Removal 4 - 16” . . . . . . . . . . . . . . . . .20
Roll Installation 4 - 16” . . . . . . . . . . . . . . . 21
Roll Installation 2 - 31/2” . . . . . . . . . . . . . . .22
Copper Roll Installation 2 - 6” and 8” . . . .23
Maintenance Procedures . . . . . . . . . . . . . . . .23
General . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Lubrication Monthly (VE416FSD Only) . . . . 24
Hydraulic Systems . . . . . . . . . . . . . . . . . . . 24
Parts Ordering Information . . . . . . . . . . . . . . . 26
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .28
Tool Rating and Roll Selection . . . . . . . . . . . .29
Standard and “ES” Rolls . . . . . . . . . . . . . .29
Schedule 5S and 10S Stain . Steel Pipe . . .30
Copper Tubing . . . . . . . . . . . . . . . . . . . . . .30
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Seamless and Welded Steel Pipe . . . . . . . . 31
Drawn Copper Tubing . . . . . . . . . . . . . . . . 31
Roll Groove Specifications . . . . . . . . . . . . . . . 32
Steel Pipe and all Materials Grooved with
Standard and “RX” Rolls . . . . . . . . . . . . . . 32
Steel Pipe and all Materials Grooved with
“ES” Rolls . . . . . . . . . . . . . . . . . . . . . . . . .33
Drawn Copper Tubing w/Copper Rolls . . . .34
READ THIS FIRST – HAZARD
IDENTIFICATION
Definitions for identifying the various hazard
levels shown on warning labels or to indicate
proper safety procedures in this Manual are
provided below .
This safety alert symbol indicates
important safety messages on
warning labels and in this manual .
When you see this symbol be alert to
the possibility of personal injury and
carefully read and fully understand
the message that follows .
DANGER
• The use of the word “DANGER” always
signifies an immediate hazard with
a likelihood of severe personal injury
or death if instructions, including
recommended precautions, are not
followed.
WARNING
• The use of the word “WARNING” signifies
the presence of hazards or unsafe
practices which could result in severe
personal injury if instructions, including
recommended precautions, are not
followed.
CAUTION
• The use of the word “CAUTION”
signifies possible hazards or unsafe
practices which could result in minor
injury, product or property damage if
instructions, including precautions, are
not followed.
NOTICE
• The use of the word “NOTICE” signifies
special instructions which are important
but not related to hazards.
TM-VE416FS/FSD_1
TM-VE416FS/FSD
OPERATING AND MAINTENANCE INSTRUCTIONS MANUAL
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.
REV_A
