background image

TABLE OF CONTENTS

Hazard Identification . . . . . . . . . . . . . . . . . 4
Operator Safety Instructions . . . . . . . . . . . . 4
Introduction  . . . . . . . . . . . . . . . . . . . . . . . 6

Receiving The Tool   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Container Contents   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Returning The Tool   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6

Tool Nomenclature. . . . . . . . . . . . . . . . . . . 7
Tool Dimensions and Specifications  . . . . . . 8
Pre-Operation Checks and Adjustments. . . . 9

Pipe Preparation   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Tool and Pipe Stand Setup .  .  .  .  .  .  .  .  .  .  .  .  .  . 9

Initial Pipe Stand Adjustments . . . . . . . . . .10
Ratchet Operation . . . . . . . . . . . . . . . . . . .12
Final Pipe Stand Adjustments. . . . . . . . . . 13
Maintenance . . . . . . . . . . . . . . . . . . . . . . .14
Parts Ordering Information . . . . . . . . . . . . .14
Troubleshooting. . . . . . . . . . . . . . . . . . . . .15

3

REV_B

TM-VAPS1672 

/ Operating and Maintenance Instructions Manual

Summary of Contents for VAPS1672

















Reviews: