background image

Auto Advance

Remote Controlled

Target System

Instruction Guide

475 Smith Street

Middletown, CT 06457

860-632-2020

www.lymanproducts.com

Lyman

®

Lyman

®

WARRANTY/REPAIR POLICY

Your Lyman product has been produced under rigid standards of manu-
facture and inspection. However, if your Lyman product is found to be de-
fective in material or workmanship within one year of delivery to the first
retail purchaser, we will repair or replace it without charge.

If you require service under this warranty, please return the complete item
along with a letter of explanation, including your complete name and ad-
dress, freight prepaid to the factory at the address listed below. Your
Lyman product will be repaired or replaced and returned to you within 30
days of our receipt. In making any return of a Lyman product to the fac-
tory, please be sure it is packaged with proper care to protect it from dam-
age in transit.

We are sorry, but our warranty cannot apply to a defect which results
from misuse, abuse, neglect, accident or improper care, or if your Lyman
product has been altered or repaired by anyone other than factory per-
sonnel.

If the item is out of warranty and is in need of repairs, the Lyman product
should also be returned to the same address listed below. Appropriate
charges will apply for parts and labor. Estimates are available only when
the item has been thoroughly inspected by our repair personnel.

Lyman Products Corporation

475 Smith Street, Middletown, CT 06457

Attn: Service Department

Summary of Contents for Auto Advance Remote Controlled Target System








Reviews: