background image

13 

8. 

Boiler operation by user 

 
The  boiler  works  automatically according to the regulation elements setting and the user only does 
the  following  service  activities  that  the  worker  who  puts  the  boiler  into  operation  is  obliged  to 
acquaint him with: 

1.  Boiler switch-off or switch-on

2.  Control of pressure in the heating system.  

 

9. 

IMPORTANT WARNINGS 

 

1. 

The boiler only can be used for the purpose that it is destined for.  

2. 

Boiler environment: it must be ensured a constant supply of fresh air. 

3. 

Boiler  can  only  be  operated  by  adult  persons  and  children  without  being  supervised  by  adults 
must not be left nearby the boiler. 

4. 

The  boiler  is  not  destined  for  the  use  by  persons  (incl.  children)  whose  physical,  sensual  or 
mental  disability  or  lack  of  experience  and  knowledge  prevent  them  from  a  safe  use  of  the 
appliance unless they are supervised or if they were not instructed on the use of appliance by a 
person responsible for their safety.  

5. 

Children should be supervised in order to ensure that they do not play with the appliance. 

6. 

If the boiler is going to be put out of operation for a long time it must be disconnected from the electricity- 
from the socket. 

7. 

In case of a failure in combustion products outlet from the combustion products draught diverter 
(countermove,  clogged  chimney)  the  combustion  products  return  flow  fuse  will  close  the  fuel 
supply to the boiler. 
The user can unblock the fuse by means of TS unblocking push-button. The boiler 
can only be restarted once the combustion products return flow fuse sensor has cooled down it means 
after 10 minutes. 

8. 

The boiler room must be kept clean and dust-free. All sources of pollution must be removed from the 
boiler room and the boiler must be put out of operation during the works (insulation works, boiler room 
cleaning)  that  cause  the  dustiness.  Even  a  partial  clogging  of  burner  with  impurities  will  degrade  the 
combustion process and endanger the economical and reliable operation of boiler. We don’t recommend 
to keep the domestic animals (like cat, dogs etc.) in boiler room. 

9. 

If there occurs the danger of development and penetration of combustible vapours or gases into 
the boiler room,
 or during the works where there arises a transient risk of fire or explosion (gluing the 
floorings,  painting  with  combustible  paints),  the  boiler  must  be  put  out  of  operation  long  enough 
before the works start.
 

10.  Don’t  put  any  objects  made  of  flammable  material  on  boiler  and  within  a  distance  smaller  than 

the safe distance from it (see chapter no. 5.2.). 

11.  In  winter  (for  example  while  leaving  for  holidays),  it  is  necessary  to  ensure  checking  of 

functionality in the necessary degree as regards the boiler and the whole heating system in order 
that water did not freeze in the system and the equipment was not damaged from some external 
reason (e.g. power failure, gas failure or similar.
 

12.  The  user  is  obliged  to  put  a  professional  contractual  service  accredited  by  VIADRUS  a.s.,  the 

boiler  manufacturer  in  trust  with  commissioning,  regular  maintenance  and  defects  elimination, 
otherwise the boiler proper function isn’t guaranteed. „VIADRUS GRAND G 36 BM boiler quality 
and  completeness  certification“  after having been filled out by contractual service organization 
serves as the „Guarantee certificate“.
 

13.  The boiler regular maintenance must be done once a year according to the next chapter. 

14.  During  assembly,  installation  and  operation  of  the  appliance  it  is  necessary  to  comply  with 

standards that apply in the relevant country of destination. 

If you fail to meet these conditions you cannot requisite the guarantee repairs.  

Summary of Contents for GRAND G 36





























































Reviews: