background image

 

  40

 

11.  Commissioning- instructions for contractual service organization 

 

The  boiler  commissioning,  heat  output  setting  and  any  interference  with  boiler  electric  part  or 
connection  of  additional  control  elements  can  only  be  done  by  a  contractual  service  organization 
authorized to do these activities. 

 

11.1  Verification activities before commissioning  

 

Before the boiler commissioning it is necessary to check: 

a)  Filling the heating system with water (check the manometer).  
b)  Adjustment of thermostats:  

boiler  thermostat  45  –  85  °C  (in  case  of  any  superior  regulation  it  is  recommended  to  set  85  °C 
temperature); 

heater  thermostat  (if  connected)  0  –  90  °C;  for  a  sufficiently  fast  HWS  heating  the  TK  boiler 
thermostat must be set to 85 °C.  

c)  Gas input pressure before entering the boiler and bleeding of the gas connection. 
d)  Connection to el. network and switching of the control thermostats 

Č

SN 33 2180 Art. 6.2.2. – the sockets 

are  to  be  connected  in  a  way  making  sure  that  the  protective  plug  is  upwards  and  the  phase  are 
connected to the left hand side socket when looking on it from the front. The same applies to the double 
sockets.  

e)  Release of bleeder screw of automatic bleeder valve. 
f)  Connection to the chimney or to smoke flue in case of forced combustion products venting.  
g)  Sparkling (for boilers in natural gas design do the check with boiler gas supply closed). 

check by listening whether there is some sparkling on the ignition electrode of ignition pilot burner; 

sparkling time depending on the used automatics; 

because the gas supply is closed there must be signalled a failure; 

„automatics unblocking“ by pushing down the ”RESET” push in network.  

h)  Check the lighting of the main burner by means of ignition pilot burner – applies to or boilers in propane 

design. 

check with boiler gas supply closed;  

check  the  gas  pressure  in  propane  reservoir  according  to  the  gas  supplier  ´s  instructions–  behind 
the  reservoir  the  pressure  must  be  min.  30  mbar  in  order  to  achieve  the  individual  boiler  outputs 
according to tab. no. 3b, 4b; 

safety interval depending on the used automatics; 

as  the  boiler  gas  supply  is  closed  the  failure  must  be  signalled  on  the  burner  automatics  (see  fig. 
no. 3); 

unblock the automatics by pushing down the “RESET” button in the network module on the control 
panel (fig. no. 28). 

 

11.2  Commissioning  

 

The boiler equipped only with network module or  an indoor thermostat (working without a superior 
regulation): 

 

1.  Open the gas closure and the water “closures“ in the heating system. 

Switch the main switch  

We switch the power switch into position I when using the external sensor otherwise we select the 
power according to our need.   

2.  In  case  everything  is  in  a  good  order  the  lighting  burner  is  lit.  From  the  lighting  burner  there  is  lit  the 

main  burner.  If  the  ignition  cycle  has  run  and  the  burner  hasn’t  been  lit  there  lights  up  the  failure 
signalling on the network module (see Fig. no. 28). If repeatedly the ignition fails it is necessary to switch 
off  the  main  switch,  detect  and  eliminate  the  failure  (see  chap.  No.  16)  and  then  repeat  the  whole 
process. 

3.  Check the gas escape. 
4.  Adjust and regulate the boiler heat output.  
5.  Stoking test. 

Boiler equipped with some of A1 - A4 regulations: 

1.  Open the gas closure and water “closures” in heating system. 
2.  Switch on the main switch on boiler panel. Connection of boiler to the electric network is signalled by the 

green light. 

3.  Bring the main switch to the position I (automatic operation). 

Summary of Contents for GARDE G 42 ECO





























































Reviews: