background image

 

23 

 

Positioning and installation 

9.1 

Regulations and directives 

Boiler  can be installed by a company holding a valid license to install and maintain the gas appliances.  A project according to the 
valid regulations must be prepared for installation. 
The  heating  system  has  to  be  filled  up  with  water,  which  complies  with  requirements  of  ČSN  07  7401,  and  mainly  its  hardness 
mustn't exceed the required parameters. 

Tab. №. 8 

 

Recommended values 

Hardness 

mmol/l 

Ca

2+

 

mmol/l 

0.3 

Concentration of total Fe + Mn 

mg/l 

(0,3)* 

*) recommended values 

WARNING!!! The manufacturer doesn't recommend using of antifreeze mixtures.  

a) for the heating system  

ČSN 06 0310 

Heat systems in buildings 

– Design and mounting 

ČSN 06 0830 

Heat systems in buildings 

– Securing devices 

ČSN 07 7401 

Water and steam for heat energetic equipment with steam operation pressure up to 8 MPa 

ČSN EN 297 

Gas  fuel  boilers  for  central  heating 

– Type B11 and B11BS fitted with atmospheric burners of nominal heat 

input not exceeding 70 kW. 

b) for  the chimney 

ČSN 73 4201 

Design of chimneys and flue gas ducts 

– Design, fulfillment and connection of fuel consumers 

c) regarding to fire-fighting regulations 

ČSN 06 1008 

Fire safety of heat equipment. 

ČSN EN 13501-1 + A1 

Fire  classification of building products and building structures 

– Part 1: Classification according to results of 

tests for reaction to fire 

d) for the hot water heating system 

ČSN 06 0320 

Heat systems in buildings 

– Preparation of hot water – Development and design 

ČSN 06 0830 

Heat systems in buildings 

– Securing devices 

ČSN 75 5409 

Indoor water distributions 

e) for electric network 

ČSN 33 0165 

Electric-technical regulations. Conductors designation with colors or numbers. Execution of provisions. 

ČSN 33 1500 

Electric-technical regulations. Revisions of electric devices. 

ČSN 33 2000-1 ed. 2 

Low voltage electric installation 

– Part 1. Basic aspects, determination of basic characteristics, definitions. 

ČSN 33 2000-4-41 ed. 2 

Low voltage electric installation 

– Part 4-41: Protective measures for provision of safety - Protection against 

electric shock. 

ČSN 33 2000-5-51 ed. 3 

Low  voltage  electric  installation 

–  Part  5-51:  Selection  and  construction  of  electric  devices  –  General 

regulations 

ČSN 33 2130 ed. 2 

Low voltage electric installation 

– Inside electric distributions. 

ČSN 33 2180 

Electric-technical regulations. Connection of electric devices and consumers. 

ČSN 34 0350 ed. 2 

Safety requirements for movable power supplies and cords. 

ČSN EN 60079-10-1 

Explosive atmospheres 

– Part 10-1: Determination of dangerous premises – Explosive gaseous atmospheres 

ČSN EN 60079-14 ed.3 

Explosive atmospheres 

– Part 14: Development, selection and performance of electric installations 

ČSN EN 60335-1 ed.2 

Electric consumers for household and similar purpose 

– Safety – Part 1: General requirements 

ČSN EN 60335-2-102 

Electric  consumers  for  household  and  similar  purpose 

–  Safety  –  Part  2-102:  Special  requirements  for 

consumers combusting gaseous, oil and solid fuels, containing electric connections. 

ČSN EN 60 445 ed. 4  

Basic  and  safety  principles  for  the  human-machine  interface,  marking  and  identification 

–  Identification  of 

clamps of subjects, ends of conductors and conductors  

f) for gas distribution 

ČSN EN 1775 

Gas supply - Gas pipelines in buildings - Maximal operation pressure <= 5 bar - Operation requirements. 

ČSN EN 12007-1 

Equipment  for  gas  supply  -  Gas  pipeline  with  maximal  operation  pressure  up  to  16  bar  including  -  Part  1: 
General functional requirements 

ČSN EN 12007-2 

Equipment  for  gas  supply  -  Gas  pipeline  with  maximal  operation  pressure  up  to  16  bar  including  -  Part  2: 
Specific functional requirements for polyethylene (maximal operation pressure up to 10 bar including)  

ČSN EN 12007-3 

Equipment  for  gas  supply  -  Gas  pipeline  with  maximal  operation  pressure  up  to  16  bar  including  -  Part  3: 
Specific functional requirements for steel  

ČSN EN 12007-4 

Equipment  for  gas  supply  -  Gas  pipeline  with  maximal  operation  pressure  up  to  16  bar  including  -  Part  4: 
Specific functional requirements for reconstruction  

ČSN 38 6405 

Gas equipment. Principles for operation. 

Law 458/2000 Sb. 

Law on conditions of enterpreneurship and on execution of public administration in energetic branches and on 
changes of some laws (the Energetic law) 

 

Summary of Contents for GARD G42 ECO













































Reviews: