060217.02
7
Remote control WRC
ENGLISH
5
Replacing batteries
From the backside remove both stainless steel clamps and remove
the rear part of the housing. Remove the electronic circuit from the
housing and replace the battery. Battery type: CR2032. Reassemble
it in reverse order.
6
Program additional transmitters
Each new transmitter must be added. A maximum of 5 transmitters
can be coupled to one receiver. If a 6
th
transmitter is added the 1
st
transmitter will be deleted from the memory of the receiver.
Make sure that the wiring of the receiver is connected and the power
supply switched on.
1. Press and hold the ‘ON’ key for about 2 seconds to switch on the
new station.
2. Press and hold the ‘PROG.’ key until the red LED lights up (4 sec.).
3. On the new transmitter, press one of the keys and keep it pressed
until the red LED in the receiver flashes.
The transmitter is now logged on. Wait for the red LED to switch
off before using the new transmitter.
7
CAN Control
CAN control is only available for Vetus V-CAN controlled thrusters.
BOWPRO thruster connection must be done through CAN-bus in-
stead of relays.
The receiver decodes the signals which are broadcasted into the V-
CAN line and detects the status of the thrusters and the requests of
the connected panels. For starting or recovering the control from the
transmitter, the user must push the ‘ON’ button. The green LED will
turn on to indicate that the device is ready for usage.
7 .1 LED indications receiver
Green and red LEDs are blinking:
Communication lost with any CAN
controlled thruster. If the communication with the other CAN con-
trolled thruster remains, it can still be used.
Once the communication with thruster is reestablished, errors can be
removed by pressing the ‘ON’ button on the remote control.
GREEN double blink:
Control taken by another control panel.
Push ‘ON’ to recover the control.
Yellow LED 1 blinking
Bow thruster overheat
Yellow LED 2 blinking
Bow thruster low voltage
Yellow LEDs 1 and 2 blinking
Bow thruster overload
Yellow LED 3 blinking
Stern thruster overheat
Yellow LED 4 blinking
Stern thruster low voltage
Yellow LEDs 3 and 4 blinking
Stern thruster overload
8
Thrust direction
By changing the system configuration, the bow/stern thruster's
thrust direction can be reversed.
LED1 flashes
standard bow thruster thrust direction
LED2 flashes
reverse bow thruster thrust direction
• To reverse the thrust direction of the bow thruster, briefly press
the 'PROG' key.
Wait for 10 seconds to exit setup mode, or
• Press and hold the "PROG" button (4sec.) until the yellow LED3 or
LED4 starts blinking.
You are now in the stern thruster, thrust direction setup mode.
Press and hold the PROG button until the
red LED lights up (4 sec.).
Press and hold the PROG button until the
yellow LED1 or LED 2 starts blinking.
You are now in the bow thruster, thrust
direction setup mode.
4 sec.
2.
3.
1.
15 sec.
2 sec.
LED3 flashes
standard stern thruster thrust direction
LED4 flashes
reverse stern thruster thrust direction
• To reverse the thrust direction of the stern thruster, briefly press
the 'PROG' key.
Wait for 10 seconds or press and hold the 'PROG' button (4 sec.) to
exit setup mode.
9
Technical specifications
Remote control
Power supply
3 VDC CR2032 (1x)
Protection class
IP66
Frequency
433.92 Hz
Temperature range
0°C - 70°C (+32°F - 158°F)
Weight
50 g (2 oz)
Receiver
Power supply
8 VDC to 30 VDC
Maximum current (per output)
8 A (at 30 Volts DC)
Protection class
IP40
Frequency
433.92 Hz
Temperature range
0°C - 70°C (+32°F - 158°F)
Weight
800 g (28 oz)
