VersaLogic Fox VL-EPM-19 Page 44 Hardware Reference Manual Download | Manualshive

Page: 44 / 61

background image

EPM-19 Hardware Reference Manual

35

Video Interfaces

An on-board video controller integrated into the Vortex86DX2 SoC provides high performance
video output for the EPM-19.

C

ONFIGURATION

The EPM-19 uses shared memory architecture. This allows the video controller to use variable
amounts of system DRAM — 8 MB, 16 MB (default), 32 MB, or 64 MB — for video RAM.
The amount of RAM used for video is set with a BIOS Setup utility option.

The EPM-19 supports two types of video output: VGA and LVDS flat panel display. A BIOS
Setup utility sub-menu (Boot Display Device) selects which output is enabled through POST.
The operating system will then take over based on the Graphic Utility CRT or LCD selection. If
the Boot Display Device selected provides incorrect timing information for an attached LCD
panel and the Graphics Utility is set to LCD, you may not see video on the output.

Refer to Table 19 on page 40 for a list of BIOS settings for boot display devices and their
corresponding resolutions.

7

«
...
42
43
44
45
46
...
»

Summary of Contents for Fox VL-EPM-19






























































Reviews:

No comments

Related manuals for Fox VL-EPM-19

Univerge SV9300

Brand: NEC Pages: 26

Brand: NEC Pages: 20

DS2000 IntraMail

Brand: NEC Pages: 2

Z3-DM8168-PCI-RPS

Brand: Z3 Technology Pages: 20

Z3-DM8107-SDI2-RPS

Brand: Z3 Technology Pages: 75

Brand: Z-Wave Pages: 13

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

JetWeb JX2-PR0FI1

Brand: Jetter Pages: 67

DHI-NVR2104-P-4KS2

Brand: Dahua Pages: 23

AIE900-XNX Series

Brand: AXIOMTEK Pages: 53

Brand: Softing Pages: 4

Brand: Eaton Pages: 14

Brand: ICP DAS USA Pages: 62

Brand: AMD Pages: 45

LEDWALL Optimizer HQ P2

Brand: Gundermann VIDEOWALL Pages: 12

Brand: Omron Pages: 432

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands