VersaLogic Fox VL-EPM-19 Hardware Reference Manual Download Page 40 | Manualshive

Page: 40 / 61

background image

EPM-19 Hardware Reference Manual

31

Serial Ports

The EPM-19 includes four on-board 16550-based serial channels located at standard PC I/O
addresses. Each COM port can be independently enabled or disabled in BIOS Setup.



All four COM ports by default are set to RS-232 mode



COM1 and COM2 are RS-232 (up to 115.2K baud) serial ports. There are no hardware
configuration jumpers for COM1 and COM2 because they only operate in RS-232 mode.
IRQ lines are chosen in the BIOS Setup utility.



COM3 and COM4 can be operated in RS-232 or RS-422/485 mode. IRQ lines are chosen in
the BIOS Setup utility.

Additional non-standard baud rates are also available through the BIOS Setup utility.

Serial Port Connectors

Figure 19 shows the location and pin orientation of the serial port connectors.

Figure 19. Location and Pin Orientation of Serial Port Connectors

6

«
...
38
39
40
41
42
...
»

Summary of Contents for Fox VL-EPM-19






























































Reviews:

No comments

Related manuals for Fox VL-EPM-19

Brand: IEI Technology Pages: 3

DIRECTOR PRO series

Brand: MF DIGITAL Pages: 79

Brand: Idis Pages: 85

Brand: Infoblox Pages: 13

640 - Pentium 4 640 3.2GHz 800MHz 2MB Socket 775 CPU

Brand: Intel Pages: 105

Brand: Digital Equipment Pages: 90

Brand: DayTronic Pages: 13

Brand: Planet Pages: 38

Brand: Acconeer Pages: 13

Rexroth IndraDrive X

Brand: Bosch Pages: 140

Brand: Cirrus Logic Pages: 102

Brand: Swyx Pages: 5

Brand: SilverStone Pages: 24

Brand: RTP Pages: 21

SMARTSTOR NS4300N

Brand: Promise Technology Pages: 186

Brand: Promise Technology Pages: 192

INSIGHT DLP SENSOR 0610S

Brand: Infolock Pages: 14

Brand: Commell Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands