manualshive.com logo in svg

VersaLogic Fox VL-EPM-19, Hardware Reference Manual, Page: 15 / 61

Share
Download
VersaLogic Fox VL-EPM-19 Hardware Reference Manual Download Page 15

Introduction 

EPM-19 Hardware Reference Manual 

6

 

The entire assembly can sit on a table top or be secured to a base plate.  When bolting the unit 
down, make sure to secure all standoffs to the mounting surface to prevent circuit board flexing. 

An extractor tool is available (part number VL-HDW-201) to separate the PC/104 modules from 
the stack. 

Related Documents 

The following documents available are on the 

EPM-19 Product Support Web Page

: 

 

EPM-19 Programmer’s Reference Manual

 – provides information on the board’s resources 

(memory, I/O, and IRQs), a description of the FPGA’s registers, and programming 
information for the board’s hardware interfaces. 

 

EPM-19_EBX-18 BIOS Reference Manual

 – provides information on accessing and 

configuring settings in the BIOS Setup utility.  All BIOS menus, submenus, and 
configuration options are described. 

 

VersaAPI Installation and Reference Guide 

– describes the shared library of API calls for 

reading and controlling on-board devices on certain VersaLogic products. 

Additional documents: 

Overview of Vortex86DX2 

http://www.vortex86.com/?p=16

 

USB 2.0 Hub and 10/100 
Ethernet Controller 

ILAN9512 Data sheet 

http://ww1.microchip.com/downloads/en/DeviceDoc/9512.pdf

 

PC/104 Specification 

http://www.versalogic.com/products/PC104/index.asp

 

PC/104-

Plus

 Specification 

http://www.versalogic.com/products/PC104/index.asp

 

 

 

Summary of Contents for Fox VL-EPM-19






























































Reviews:

No comments