VersaLogic Fox VL-EPM-19 Page 31 Hardware Reference Manual Download | Manualshive

Page: 31 / 61

background image

EPM-19 Hardware Reference Manual

22

Mass Storage Interfaces

SATA

The EPM-19 provides a 1.5 Gbit/s SATA port. Power to the SATA drive is usually provided by
the ATX power supply. Note that the standard SATA drive power connector is different from
the typical 4-pin Molex connector used on IDE drives. Most current ATX power supplies
provide SATA connectors, and many SATA drives provide both types of power connectors. If
the power supply you are using does not provide SATA connectors, adapters are available.



Integrator’s Note:

Only one SATA port is available on the Vortex86DX2 chip, so only the J10 SATA port or the J2
mSATA port can be used; both cannot be used at the same time. Whenever J2 has an mSATA
card installed, the mSATA card uses the single SATA port.

Figure 14. Location of the SATA Port

4

«
...
29
30
31
32
33
...
»

Summary of Contents for Fox VL-EPM-19






























































Reviews:

No comments

Related manuals for Fox VL-EPM-19

Brand: Barco Pages: 100

Brand: Sangoma Pages: 6

Brand: Rane Pages: 4

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 6

Brand: ebm-papst Pages: 5

Brand: Commell Pages: 58

Brand: SIIG Pages: 12

Brand: IEI Technology Pages: 86

Lite N42B1P Series

Brand: Dahua Technology Pages: 14

Brand: Keithley Pages: 71

PCH1 T P Series

Brand: Parker Pages: 107

Brand: MC Pages: 21

Brand: Omron Pages: 13

Brand: MICROENER Pages: 24

Brand: ICS ELECTRONICS Pages: 4

SPEEDTOUCH 110G

Brand: THOMSON Pages: 26

WISENET XRN-1610

Brand: Hanwha Techwin Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands